Ubuntu 10.10 下配置Telnet服务器
2015-03-23 19:46
288 查看
首先说明我的系统环境:Ubuntu 10.10
x86 Desktop
在这个系统上默认只安装了telnet(也就是client)
所以只能用telnet命令登录别人开启telnet服务的主机,其他人是不能使用telnet登录本机的。
1,现在要说的就是让别人能够使用telnet登录本机,需要安装两个软件:
其中telnetd是telnet-server,但它是无法自我启动的,需要管理daemon的软件xinetd来接管。
2,通过xinetd启动telnetd,方法是新建telnet文件,并输入如下内容(没有安全性设置)
如果要修改telnet的默认端口号(23),需要修改/etc/services文件中对应的telnet
3,然后重启xinetd程序
这时候可以是使用netstat命令查看23端口监听情况
4,可以确定telnet服务器已经搭建完成,这时只需要换个电脑,然后使用telnet ip即可登录。默认的设定是root不能通过telnet登录(telnet在网络上是明文传输,可以被sniffer侦测出密码),如果安全性有保证,可以通过一下方法允许root登录:
(1)修改/etc/securetty文件,添加终端
或者直接将securetty文件改名,即可使用root登录
(2)修改/etc/pam.d/login文件,将securetty验证注释调
这样telnet基本上就配置完成了,不过还是建议大家用ssh(但windows系统要用ssh还要附加专门的软件,真的很艹蛋!
http://www.linuxidc.com/Linux/2011-10/44291.htm
x86 Desktop
在这个系统上默认只安装了telnet(也就是client)
root@www.linuxidc.com:~# dpkg -s telnet Package: telnet Status: install ok installed Priority: standard Section: net Installed-Size: 188 Maintainer: Ubuntu Developers <ubuntu-devel-discuss@lists.ubuntu.com> Architecture: i386 Source: netkit-telnet Version: 0.17-36build1 Replaces: netstd Provides: telnet-client
所以只能用telnet命令登录别人开启telnet服务的主机,其他人是不能使用telnet登录本机的。
1,现在要说的就是让别人能够使用telnet登录本机,需要安装两个软件:
root@www.linuxidc.com:~# apt-get install telnetd root@www.linuxidc.com:~# apt-get install xinetd
其中telnetd是telnet-server,但它是无法自我启动的,需要管理daemon的软件xinetd来接管。
root@www.linuxidc.com:~# dpkg -s telnetd Package: telnetd Status: install ok installed Priority: optional Section: net Installed-Size: 152 Maintainer: Ubuntu Developers <ubuntu-devel-discuss@lists.ubuntu.com> Architecture: i386 Source: netkit-telnet Version: 0.17-36build1 Replaces: netstd Provides: telnet-server
2,通过xinetd启动telnetd,方法是新建telnet文件,并输入如下内容(没有安全性设置)
root@www.linuxidc.com:~#vi /etc/xinetd.d/telnet service telnet { disable = no socket_type = stream flags = REUSE wait = no user = root server = /usr/sbin/in.telnetd #特别注意此处,in.telnetd是telnetd安装产生的文件 log_on_failure += USERID }
如果要修改telnet的默认端口号(23),需要修改/etc/services文件中对应的telnet
3,然后重启xinetd程序
root@www.linuxidc.com:/etc/xinetd.d# service xinetd restart * Stopping internet superserver xinetd [ OK ] * Starting internet superserver xinetd [ OK ]
这时候可以是使用netstat命令查看23端口监听情况
root@www.linuxidc.com:~# netstat -tulnp | grep 23 tcp 0 0 0.0.0.0:23 0.0.0.0:* LISTEN 4176/xinetd
4,可以确定telnet服务器已经搭建完成,这时只需要换个电脑,然后使用telnet ip即可登录。默认的设定是root不能通过telnet登录(telnet在网络上是明文传输,可以被sniffer侦测出密码),如果安全性有保证,可以通过一下方法允许root登录:
(1)修改/etc/securetty文件,添加终端
root@www.linuxidc.com:~# tail -5 /etc/securetty pts/0 pts/1 pts/2 pts/3 pts/4
或者直接将securetty文件改名,即可使用root登录
(2)修改/etc/pam.d/login文件,将securetty验证注释调
12 # Disallows root logins except on tty's listed in /etc/securetty 13 # (Replaces the `CONSOLE' setting from login.defs) 14 # Note that it is included as a "required" module. root will be 15 # prompted for a password on insecure ttys. 16 # If you change it to a "requisite" module, make sure this does not leak 17 # user name information. 18 #auth required pam_securetty.so
这样telnet基本上就配置完成了,不过还是建议大家用ssh(但windows系统要用ssh还要附加专门的软件,真的很艹蛋!
http://www.linuxidc.com/Linux/2011-10/44291.htm
相关文章推荐
- Ubuntu Telnet服务器与SSH服务器的配置
- Ubuntu如何配置Telnet服务器
- Ubuntu(六):telnet服务器的配置
- Ubuntu10.10下安装配置tftp服务器
- Ubuntu10.10配置与安装DHCP服务器
- ubuntu 安装telnet服务器及配置
- Ubuntu下配置Telnet服务器
- Ubuntu配置Telnet服务器
- Ubuntu下配置Telnet服务器
- Ubuntu下配置Telnet服务器
- Ubuntu下Telnet服务器的配置方法
- Ubuntu下配置Telnet服务器
- Ubuntu Server 10.10 DNS服务器的配置方法
- Ubuntu10.10配置与安装DHCP服务器
- ubuntu10.10 telnet 配置
- Ubuntu 10.10 Telnet 配置
- Ubuntu(六):telnet服务器的配置
- Ubuntu安装配置Apache2服务器
- Ubuntu下FTP服务器的配置