Cisco 交换机配置文件恢复实践--TFTP 方式
2013-11-18 19:10
423 查看
这是我在公司写的指导文档,所以是英文的,水平有点低,勿喷....IP 地址均为临时使用的,但都实验成功。
1.Setup TFTP file server by run Cisco TFTP Serversoftware, or other TFTP Server software(e.g.SolarWindsTFTPServer) and set the root directory.
Cisco TFTP:
SolarWinds TFTP Server:
2.Copy the running-config file for the switchwhich before stored to the rootdirectory of the TFTP server.
3.Connect new Switch to TFTP server with Ethernet port, to laptop/PC with console port.
(the second method only need one PC ,It’s aPractical solution.) configure the IP address setting of the PC that running TFTPserver software.
4.Run Putty as the following configuration .
5.Power on the Switch, follow the initial configuration dialog guide. Configure the switch.
Or input “NO” Skip the step, and then configureVLAN1 .
The IP address forVLAN1 must be in same subnet with the IP address of PC that running TFTPSoftware.
6.Use “copy TFTP startup-config” to copy the running –config file to nvram afterenter EXEC mode. Commands as the above picture shows.
7.Power off the switch. use it to replace the specified one. Then power on the switch. Replacement Done.
本文出自 “奋斗的菜鸟” 博客,谢绝转载!
1.Setup TFTP file server by run Cisco TFTP Serversoftware, or other TFTP Server software(e.g.SolarWindsTFTPServer) and set the root directory.
Cisco TFTP:
SolarWinds TFTP Server:
2.Copy the running-config file for the switchwhich before stored to the rootdirectory of the TFTP server.
3.Connect new Switch to TFTP server with Ethernet port, to laptop/PC with console port.
(the second method only need one PC ,It’s aPractical solution.) configure the IP address setting of the PC that running TFTPserver software.
4.Run Putty as the following configuration .
5.Power on the Switch, follow the initial configuration dialog guide. Configure the switch.
Or input “NO” Skip the step, and then configureVLAN1 .
The IP address forVLAN1 must be in same subnet with the IP address of PC that running TFTPSoftware.
6.Use “copy TFTP startup-config” to copy the running –config file to nvram afterenter EXEC mode. Commands as the above picture shows.
7.Power off the switch. use it to replace the specified one. Then power on the switch. Replacement Done.
本文出自 “奋斗的菜鸟” 博客,谢绝转载!
相关文章推荐
- 使用TFTP服务器备份与恢复CISCO配置文件
- cisco 通过tftp备份/恢复配置和3560交换机IOS升级
- CISCO路由器/交换机的配置文件备份及还原
- CISCO-2950交换机密码恢复(不破坏原配置)
- 在cisco路由器上使用TFTP备份/恢复交换路由的IOS文件
- H3C Tftp备份与恢复配置文件
- CISCO-2950交换机密码恢复(不破坏原配置)
- CISCO路由器/交换机的配置文件备份及还原
- Cisco 3750交换机配置无故丢失,恢复一例
- Cisco 交换机配置文件存放位置及管理要点
- CISCO 交换机配置 Web浏览器的方式
- 配置文件恢复
- cisco 交换机 VTP 配置
- 加载配置文件的四种方式
- Spring-boot中读取核心配置文件application和自定义properties配置文件的方式
- java获取工程目录下面或者引用jar包中的配置文件方式:
- Spring整理12 -- 面对切面(AOP)2 -- 配置文件的方式实现AOP
- 用类加载器的方式管理资源和配置文件
- C#中采用自定义方式读取自定义配置文件