简单聊聊Qos—优先级队列 PQ

在优先级队列PQ中，有 高 中 普通 低四个优先级队列。数据包根据实现的定义放在不同的队列中，路由器按照高 中 普通 低顺序进行服务，只有高优先级的队列为空后，才为其他的优先级队列服务，以此类推，这样能保证高优先级数据包一定是优先服务。

实验拓扑如下





实验准备：

做通全网 实现内部私有地址可以和任何一个公网地址进行通信 （R4 的环回接口 4.4.4.4 模拟私网地址) 该准备阶段的过程略

PQ配置过程

R2(config)#priority-list ? 启用PQ

<1-16> Priority list number

R2(config)#priority-list 1 ? 定义PQ序号

default Set priority queue for unspecified datagrams

interface Establish priorities for packets from a named interface

protocol priority queueing by protocol

queue-limit Set queue limits for priority queues

R2(config)#priority-list 1 pro

R2(config)#priority-list 1 protocol ?

aarp AppleTalk ARP

appletalk AppleTalk

arp IP ARP

bridge Bridging

bstun Block Serial Tunnel

cdp Cisco Discovery Protocol

clns ISO CLNS

clns_es ISO CLNS End System

clns_is ISO CLNS Intermediate System

cmns ISO CMNS

compressedtcp Compressed TCP (VJ)

decnet DECnet

decnet_node DECnet Node

decnet_router-l1 DECnet Router L1

decnet_router-l2 DECnet Router L2

dlsw Data Link Switching (Direct encapsulation only)

http HTTP

ip IP

ipv6 IPV6

ipx Novell IPX

llc2 llc2

pad PAD links

R2(config)#priority-list 1 protocol ip 配置IP协议的优先级列表

R2(config)#priority-list 1 protocol ip ? 指定优先级

high

medium

normal

low

R2(config)#priority-list 1 protocol ip high ? 指定优先级为高

fragments Prioritize fragmented IP packets

gt Prioritize packets greater than a specified size

list To specify an access list

lt Prioritize packets less than a specified size

tcp Prioritize TCP packets 'to' or 'from' the specified port

udp Prioritize UDP packets 'to' or 'from' the specified port

<cr>

R2(config)#priority-list 1 protocol ip high tcp ? TCP流量

<0-65535> Port number

bgp Border Gateway Protocol (179)

chargen Character generator (19)

cmd Remote commands (rcmd, 514)

daytime Daytime (13)

discard Discard (9)

domain Domain Name Service (53)

drip Dynamic Routing Information Protocol (3949)

echo Echo (7)

exec Exec (rsh, 512)

finger Finger (79)

ftp File Transfer Protocol (21)

ftp-data FTP data connections (20)

gopher Gopher (70)

hostname NIC hostname server (101)

ident Ident Protocol (113)

irc Internet Relay Chat (194)

klogin Kerberos login (543)

kshell Kerberos shell (544)

login Login (rlogin, 513)

lpd Printer service (515)

nntp Network News Transport Protocol (119)

R2(config)#priority-list 1 protocol ip high tcp telnet

配置了一个优先级序列 序列号为1 tcp 的telnet 流量优先级为高

R2(config)#access-list 10 permit host 192.168.100.2 定义了一个ACL

R2(config)#priorit

R2(config)#priority-list 1 proto

R2(config)#priority-list 1 protocol ip high ?

fragments Prioritize fragmented IP packets

gt Prioritize packets greater than a specified size

list To specify an access list

lt Prioritize packets less than a specified size

tcp Prioritize TCP packets 'to' or 'from' the specified port

udp Prioritize UDP packets 'to' or 'from' the specified port

<cr>

R2(config)#priority-list 1 protocol ip high list ?

<1-199> IP access list

<1300-2699> IP expanded access list

R2(config)#priority-list 1 protocol ip high list 10 ?

定义了所有来自该ACL的流量优先级为高

<cr>

R2(config)#priority-list 1 protocol ip medium ?

fragments Prioritize fragmented IP packets

gt Prioritize packets greater than a specified size

list To specify an access list

lt Prioritize packets less than a specified size

tcp Prioritize TCP packets 'to' or 'from' the specified port

udp Prioritize UDP packets 'to' or 'from' the specified port

<cr>

R2(config)#priority-list 1 protocol ip medium gt 1000 数据包大小大于1000优先级为中

R2(config)#priority-list 1 interface f1/0 normal 来自端口 f0/1的流量优先级为普通

R2(config)#priority-list 1 default low 其他流量优先级为底

R2(config)#priority-list 1 queue-limit 20 30 40 50 指定序列深度

R2(config)#int f1/0

R2(config-if)#prio

R2(config-if)#priority-group 1 ?

<cr>

将策略应用到接口

实验调试：

检查端口上的序列

R2#show interfaces f1/0

FastEthernet1/0 is up, line protocol is up

Hardware is i82543 (Livengood), address is ca01.11ec.001c (bia ca01.11ec.001c)

Internet address is 12.1.1.2/24

MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 100Mb/s, 100BaseTX/FX

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:00, output 00:00:04, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: priority-list 1 该端口和序列相关联

查看队列配置

R2#show queueing priority

Current DLCI priority queue configuration:

Current priority queue configuration:

List Queue Args

1 low default

1 high protocol ip tcp port telnet

1 high protocol ip list 10

1 medium protocol ip gt 1000

1 normal interface FastEthernet1/0

1 medium limit 30

1 normal limit 40

1 low limit 50

上述为我们定义的 PQ策略

策略的检测

R2#debug priority

Priority output queueing debugging is on 在R2上开启debug









我们发现 ping 流量的优先级是 low









我们看到 telnet 的流量是 high PQ 优先级队列的实验就结束了