路由器配置基础--设置对话过程
2001-05-25 22:43
816 查看
路由器配置基础--设置对话过程
推荐:longertree 发表日期:2001年5月24日 阅读次数:17
--------------------------------------------------------------------------------
相关文章
• 路由器配置基础--命令状态
三、设置对话过程
1.显示提示信息
2.全局参数的设置
3.接口参数的设置
4.显示结果
利用设置对话过程可以避免手工输入命令的烦琐,但它还不能完全代替手工设置,一些特殊的设置还必须通过手工输入的方式完成。
进入设置对话过程后,路由器首先会显示一些提示信息:
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
这是告诉你在设置对话过程中的任何地方都可以键入“?”得到系统的帮助,按ctrl-c可以退出设置过程,缺省设置将显示在‘[]’中。然后路由器会问是否进入设置对话:
Would you like to enter the initial configuration dialog? [yes]:
如果按y或回车,路由器就会进入设置对话过程。首先你可以看到各端口当前的状况:
First, would you like to see the current interface summary? [yes]:
Any interface listed with OK? value "NO" does not have a valid configuration
Interface
IP-Address
OK?
Method
Status
Protocol
Ethernet0
unassigned
NO
unset
up
up
Serial0
unassigned
NO
unset
up
up
………
………
…
……
…
…
然后,路由器就开始全局参数的设置:
Configuring global parameters:
1.设置路由器名:
Enter host name [Router]:
2.设置进入特权状态的密文(secret),此密文在设置以后不会以明文方式显示:
The enable secret is a one-way cryptographic secret used
instead of the enable password when it exists.
Enter enable secret: cisco
3.设置进入特权状态的密码(password),此密码只在没有密文时起作用,并且在设置以后会以明文方式显示:
The enable password is used when there is no enable secret
and when using older software and some boot images.
Enter enable password: pass
4.设置虚拟终端访问时的密码:
Enter virtual terminal password: cisco
5.询问是否要设置路由器支持的各种网络协议:
Configure SNMP Network Management? [yes]:
Configure DECnet? [no]:
Configure AppleTalk? [no]:
Configure IPX? [no]:
Configure IP? [yes]:
Configure IGRP routing? [yes]:
Configure RIP routing? [no]:
………
6.如果配置的是拨号访问服务器,系统还会设置异步口的参数:
Configure Async lines? [yes]:
1) 设置线路的最高速度:
Async line speed [9600]:
2) 是否使用硬件流控:
Configure for HW flow control? [yes]:
3) 是否设置modem:
Configure for modems? [yes/no]: yes
4) 是否使用默认的modem命令:
Configure for default chat script? [yes]:
5) 是否设置异步口的PPP参数:
Configure for Dial-in IP SLIP/PPP access? [no]: yes
6) 是否使用动态IP地址:
Configure for Dynamic IP addresses? [yes]:
7) 是否使用缺省IP地址:
Configure Default IP addresses? [no]: yes
8) 是否使用TCP头压缩:
Configure for TCP Header Compression? [yes]:
9) 是否在异步口上使用路由表更新:
Configure for routing updates on async links? [no]: y
10) 是否设置异步口上的其它协议。
接下来,系统会对每个接口进行参数的设置。
1.Configuring interface Ethernet0:
1) 是否使用此接口:
Is this interface in use? [yes]:
2) 是否设置此接口的IP参数:
Configure IP on this interface? [yes]:
3) 设置接口的IP地址:
IP address for this interface: 192.168.162.2
4) 设置接口的IP子网掩码:
Number of bits in subnet field [0]:
Class C network is 192.168.162.0, 0 subnet bits; mask is /24
在设置完所有接口的参数后,系统会把整个设置对话过程的结果显示出来:
The following configuration command script was created:
hostname Router
enable secret 5 $1$W5Oh$p6J7tIgRMBOIKVXVG53Uh1
enable password pass
…………
请注意在enable secret后面显示的是乱码,而enable password后面显示的是设置的内容。
显示结束后,系统会问是否使用这个设置:
Use this configuration? [yes/no]: yes
如果回答yes,系统就会把设置的结果存入路由器的NVRAM中,然后结束设置对话过程,使路由器开始正常的工作。
原作者:不详
来源:瑞安在线
推荐:longertree 发表日期:2001年5月24日 阅读次数:17
--------------------------------------------------------------------------------
相关文章
• 路由器配置基础--命令状态
三、设置对话过程
1.显示提示信息
2.全局参数的设置
3.接口参数的设置
4.显示结果
利用设置对话过程可以避免手工输入命令的烦琐,但它还不能完全代替手工设置,一些特殊的设置还必须通过手工输入的方式完成。
进入设置对话过程后,路由器首先会显示一些提示信息:
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
这是告诉你在设置对话过程中的任何地方都可以键入“?”得到系统的帮助,按ctrl-c可以退出设置过程,缺省设置将显示在‘[]’中。然后路由器会问是否进入设置对话:
Would you like to enter the initial configuration dialog? [yes]:
如果按y或回车,路由器就会进入设置对话过程。首先你可以看到各端口当前的状况:
First, would you like to see the current interface summary? [yes]:
Any interface listed with OK? value "NO" does not have a valid configuration
Interface
IP-Address
OK?
Method
Status
Protocol
Ethernet0
unassigned
NO
unset
up
up
Serial0
unassigned
NO
unset
up
up
………
………
…
……
…
…
然后,路由器就开始全局参数的设置:
Configuring global parameters:
1.设置路由器名:
Enter host name [Router]:
2.设置进入特权状态的密文(secret),此密文在设置以后不会以明文方式显示:
The enable secret is a one-way cryptographic secret used
instead of the enable password when it exists.
Enter enable secret: cisco
3.设置进入特权状态的密码(password),此密码只在没有密文时起作用,并且在设置以后会以明文方式显示:
The enable password is used when there is no enable secret
and when using older software and some boot images.
Enter enable password: pass
4.设置虚拟终端访问时的密码:
Enter virtual terminal password: cisco
5.询问是否要设置路由器支持的各种网络协议:
Configure SNMP Network Management? [yes]:
Configure DECnet? [no]:
Configure AppleTalk? [no]:
Configure IPX? [no]:
Configure IP? [yes]:
Configure IGRP routing? [yes]:
Configure RIP routing? [no]:
………
6.如果配置的是拨号访问服务器,系统还会设置异步口的参数:
Configure Async lines? [yes]:
1) 设置线路的最高速度:
Async line speed [9600]:
2) 是否使用硬件流控:
Configure for HW flow control? [yes]:
3) 是否设置modem:
Configure for modems? [yes/no]: yes
4) 是否使用默认的modem命令:
Configure for default chat script? [yes]:
5) 是否设置异步口的PPP参数:
Configure for Dial-in IP SLIP/PPP access? [no]: yes
6) 是否使用动态IP地址:
Configure for Dynamic IP addresses? [yes]:
7) 是否使用缺省IP地址:
Configure Default IP addresses? [no]: yes
8) 是否使用TCP头压缩:
Configure for TCP Header Compression? [yes]:
9) 是否在异步口上使用路由表更新:
Configure for routing updates on async links? [no]: y
10) 是否设置异步口上的其它协议。
接下来,系统会对每个接口进行参数的设置。
1.Configuring interface Ethernet0:
1) 是否使用此接口:
Is this interface in use? [yes]:
2) 是否设置此接口的IP参数:
Configure IP on this interface? [yes]:
3) 设置接口的IP地址:
IP address for this interface: 192.168.162.2
4) 设置接口的IP子网掩码:
Number of bits in subnet field [0]:
Class C network is 192.168.162.0, 0 subnet bits; mask is /24
在设置完所有接口的参数后,系统会把整个设置对话过程的结果显示出来:
The following configuration command script was created:
hostname Router
enable secret 5 $1$W5Oh$p6J7tIgRMBOIKVXVG53Uh1
enable password pass
…………
请注意在enable secret后面显示的是乱码,而enable password后面显示的是设置的内容。
显示结束后,系统会问是否使用这个设置:
Use this configuration? [yes/no]: yes
如果回答yes,系统就会把设置的结果存入路由器的NVRAM中,然后结束设置对话过程,使路由器开始正常的工作。
原作者:不详
来源:瑞安在线
相关文章推荐
- cisco思科路由器设置对话过程(本文转载自:www.91ccie.com
- Cisco路由器基础信息配置---设置时间,警告信息和端口信息
- 路由器的修改权限密码、还原出厂设置、备份配置文件和升级操作系统实际操作
- 2610XM路由器的恢复出厂设置,备份配置文件,修改密码,以及升级
- 路由器的修改特权密码、还原出厂设置、备份配置文件和升级操作系统
- 路由器的恢复出厂设置、修改特权密码、备份配置文件和升级操作系统实际操作
- Cisco路由器基本设置(基础 下篇 )
- 通过路由器基础设置 使网络更加安全【绿色】
- 路由器的登录和基础配置
- 用于设置和管理路由的路由器配置示例
- 路由器设置基础知识(一)
- mac配置Android 环境,完整过程,其中包括遇到的设置$JAVA_HOME问题,新建项目报 Errors running builder 'Android Resource Manager问题
- 路由器配置基础
- VRP系统——路由器配置之信息中心基础
- 路由器的修改特权密码、还原出厂设置、备份配置文件和升级操作系统实际操作
- 路由器设置基础知识(二)
- USB开发基础--USB Monitor2.26 实例讲解USB的枚举(配置)过程
- 路由器的修改特权密码、还原出厂设置、备份配置文件和升级操作系统实际操作