华为无线-AC+AP小型无线网络配置实验_v1
2017-11-20 16:46
956 查看
允许转载,但必须注明出版处与原文链接,否则追究其法律责任,谢谢合作!
华为无线-AC+AP小型无线网络配置实验_v1网络结构图:
步骤一:配置网络连通性SW:interface Vlanif100ip address 192.168.0.1 255.255.255.0
interface GigabitEthernet0/0/1port link-type trunkport trunk pvid vlan 100port trunk allow-pass vlan 2 to 4094
interface GigabitEthernet0/0/2port link-type trunkport trunk pvid vlan 100port trunk allow-pass vlan 2 to 4094最终实现目标与解释:交换机G0/0/2与G/0/0/1接口通过Vlan100 进行连通,为了AP与AC之间能通讯。
AC:interface Vlanif100ip address 192.168.0.2 255.255.255.0dhcp select interface
interface GigabitEthernet0/0/1port link-type trunkport trunk pvid vlan 100port trunk allow-pass vlan 2 to 4094最终实现目标与解释:AC的G/0/01接口与交换机的G/0/0/1接口通过Vlan100 进行连通,为了AP与AC之间能通讯。Vlan100接口做为管理网络的DHCP,注意AC与AP通讯路过的接口都要打上 pvid vlan 100。
步骤二:配置AP上线到ACAC:wlan ac-global country-code cn(默认)wlan ac-global carrier id other ac id 1
wlanwlan ac source interface vlanif100ap-region id 10ap-region-name testap-auth-mode mac-auth(默认)
ap id 0 type-id 19 mac 00e0-fc2c-72f0ap-sysname test-1region-id 10最终实现目标与解释:在Wlan视图下,指定AC的Vlan100接口作为AP上线通讯接口,创建一个AP组 ID为10,命名为test。通过手动mac方式添加AP, type-id 19为AP型号对应的ID编号,AP命名为test-1并加入相应的组。
步骤三:放出Wifi信号interface Vlanif101ip address 192.168.101.1 255.255.255.0dhcp select interface
interface Wlan-Ess1port hybrid pvid vlan 101port hybrid untagged vlan 101最终实现目标与解释:为无线用户提供一个DHCP服务,使用Vlan101接口做DHCP。创建一个虚拟二层接口Ess1,以普通物理二层接口功能差不多。
wlanwmm-profile name wmm id 1radio-profile name radio id 1wmm-profile id 1最终实现目标与解释:wmm相当于Qos,主要用于质量控制,需要绑到射频模板上使用。创建一个射频模板,某个射频调用了它,该射频就拥继承模板上的参数。
traffic-profile name traffic id 1security-profile name security id 1最终实现目标与解释:创建一个流量模样和一个安全模板,可以不配置参数,但必须创建并加到服务集中。
wlanservice-set name test id 1forward-mode tunnelssid test-xcwwlan-ess 1service-vlan 101traffic-profile id 1security-profile id 1最终实现目标与解释:创建一个服务集,用于射频调用,里边集成了各种刚刚创建的模板。
ap 0 radio 0radio-profile id 1service-set id 1 wlan 1最终实现目标与解释:在AP 0上的0=2.4G射频上调用射频模板与服务集。
commit ap 0最终实现目标与解释:最后在Wlan视图下提交AP的配置才会放出Wifi信号。
步骤四:让用户访问互联网网络结构图:
由于无线用户是通过AC上的Vlan101接口的DHCP获取IP地址,所以网关为Vlan101的地址(192.168.101.1),由于访问其它网段需要路由,建议使用动态路由协议OSPF。 在AR、SW、AC之间建立一个OSPF-AREA,并公布相关网段。本文不作OSPF研究,如需要了解OSPF配置知识,后续会出相关文章。
--END
华为无线-AC+AP小型无线网络配置实验_v1网络结构图:
步骤一:配置网络连通性SW:interface Vlanif100ip address 192.168.0.1 255.255.255.0
interface GigabitEthernet0/0/1port link-type trunkport trunk pvid vlan 100port trunk allow-pass vlan 2 to 4094
interface GigabitEthernet0/0/2port link-type trunkport trunk pvid vlan 100port trunk allow-pass vlan 2 to 4094最终实现目标与解释:交换机G0/0/2与G/0/0/1接口通过Vlan100 进行连通,为了AP与AC之间能通讯。
AC:interface Vlanif100ip address 192.168.0.2 255.255.255.0dhcp select interface
interface GigabitEthernet0/0/1port link-type trunkport trunk pvid vlan 100port trunk allow-pass vlan 2 to 4094最终实现目标与解释:AC的G/0/01接口与交换机的G/0/0/1接口通过Vlan100 进行连通,为了AP与AC之间能通讯。Vlan100接口做为管理网络的DHCP,注意AC与AP通讯路过的接口都要打上 pvid vlan 100。
步骤二:配置AP上线到ACAC:wlan ac-global country-code cn(默认)wlan ac-global carrier id other ac id 1
wlanwlan ac source interface vlanif100ap-region id 10ap-region-name testap-auth-mode mac-auth(默认)
ap id 0 type-id 19 mac 00e0-fc2c-72f0ap-sysname test-1region-id 10最终实现目标与解释:在Wlan视图下,指定AC的Vlan100接口作为AP上线通讯接口,创建一个AP组 ID为10,命名为test。通过手动mac方式添加AP, type-id 19为AP型号对应的ID编号,AP命名为test-1并加入相应的组。
步骤三:放出Wifi信号interface Vlanif101ip address 192.168.101.1 255.255.255.0dhcp select interface
interface Wlan-Ess1port hybrid pvid vlan 101port hybrid untagged vlan 101最终实现目标与解释:为无线用户提供一个DHCP服务,使用Vlan101接口做DHCP。创建一个虚拟二层接口Ess1,以普通物理二层接口功能差不多。
wlanwmm-profile name wmm id 1radio-profile name radio id 1wmm-profile id 1最终实现目标与解释:wmm相当于Qos,主要用于质量控制,需要绑到射频模板上使用。创建一个射频模板,某个射频调用了它,该射频就拥继承模板上的参数。
traffic-profile name traffic id 1security-profile name security id 1最终实现目标与解释:创建一个流量模样和一个安全模板,可以不配置参数,但必须创建并加到服务集中。
wlanservice-set name test id 1forward-mode tunnelssid test-xcwwlan-ess 1service-vlan 101traffic-profile id 1security-profile id 1最终实现目标与解释:创建一个服务集,用于射频调用,里边集成了各种刚刚创建的模板。
ap 0 radio 0radio-profile id 1service-set id 1 wlan 1最终实现目标与解释:在AP 0上的0=2.4G射频上调用射频模板与服务集。
commit ap 0最终实现目标与解释:最后在Wlan视图下提交AP的配置才会放出Wifi信号。
步骤四:让用户访问互联网网络结构图:
由于无线用户是通过AC上的Vlan101接口的DHCP获取IP地址,所以网关为Vlan101的地址(192.168.101.1),由于访问其它网段需要路由,建议使用动态路由协议OSPF。 在AR、SW、AC之间建立一个OSPF-AREA,并公布相关网段。本文不作OSPF研究,如需要了解OSPF配置知识,后续会出相关文章。
--END
相关文章推荐
- 华为AC-AP配置
- 华为无线网络AC下的有线可以上网,无线无法ping通网关,无法上网的解决办法
- Win7无线配置工具VC++(Soft-Ap,Wifi,无线承载网络,ICS,Wifi)
- 小型企业默认路由使用及配置实验 —华为
- Win7无线配置工具VC++(Soft-Ap,Wifi,无线承载网络,ICS,Wifi)
- 【华为WLAN】WLAN网络,AC旁挂直接转发基本配置。
- windows XP系统搜索无线网络时提示“windows无法配置此无线连接”,如何处理?
- wpa_supplicant & wpa_cli 无线网络配置
- 联想Y430P CentOS 7.3 无线网络的配置
- <WIFI>在soft-AP模式下实现配置UDP实验——手机点灯
- Ubuntu 无线网络配置
- 在Linux上配置无线网络
- centos7 无线网卡驱动的安装及无线网络的配置详解
- 网络实验(五路由器的基本配置)
- 无线网络配置
- Gentoo 无线网络配置 wpa_supplicant
- 企业小型网络的配置
- 修改无线wifi网络名称。注册表。windows 无线属性 windows 无线 配置文件
- 【华为实验】AAA本地认证和hwtacacs配置并存的情况总结
- CCNA网络系列实验(1)之GNS3安装配置指南