CentOS7使用firewalld打开关闭防火墙与端口
2017-08-09 21:27
253 查看
CentOS 7 默认没有使用iptables,所以通过编辑iptables的配置文件来开启80端口是不可以的
CentOS 7 采用了 firewalld 防火墙
如要查询是否开启80端口则:
显然80端口没有开启
下面我们开启80端口:
启动一个服务:systemctl start firewalld.service
关闭一个服务:systemctl stop firewalld.service
重启一个服务:systemctl restart firewalld.service
显示一个服务的状态:systemctl status firewalld.service
在开机时启用一个服务:systemctl enable firewalld.service
在开机时禁用一个服务:systemctl disable firewalld.service
查看服务是否开机启动:systemctl is-enabled firewalld.service
查看已启动的服务列表:systemctl list-unit-files|grep enabled
查看启动失败的服务列表:systemctl --failed
3.配置firewalld-cmd
查看版本: firewall-cmd --version 查看帮助: firewall-cmd --help 显示状态: firewall-cmd --state 查看所有打开的端口: firewall-cmd --zone=public --list-ports 更新防火墙规则: firewall-cmd --reload 查看区域信息: firewall-cmd --get-active-zones 查看指定接口所属区域: firewall-cmd --get-zone-of-interface=eth0 拒绝所有包:firewall-cmd --panic-on 取消拒绝状态: firewall-cmd --panic-off 查看是否拒绝: firewall-cmd --query-panic 那怎么开启一个端口呢 添加 firewall-cmd --zone=public --add-port=80/tcp --permanent (--permanent永久生效,没有此参数重启后失效) 重新载入 firewall-cmd --reload 查看 firewall-cmd --zone= public --query-port=80/tcp 删除 firewall-cmd --zone= public --remove-port=80/tcp --permanent相关文章推荐
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口(转载)
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- 莫小安 CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口(转载)
- CentOS7使用firewalld打开关闭防火墙、端口
- 详解CentOS7使用firewalld打开关闭防火墙与端口
- CentOS7使用firewalld打开关闭防火墙与端口