virtualbox虚拟机NAT模式下不能连接外网
2017-02-22 05:18
267 查看
背景
给VirtualBox虚拟机(装载了Ubuntu16.04系统)配置了两张网卡,网络模式分别为“网络地址转换(NAT)”和“仅主机(Host-Only)适配器”,其中,enp0s3网卡(NAT)用于外网访问,而enp0s8网卡(Host-Only)用于主机访问虚拟机。然而,虚拟机启动后,却不能访问外网。定位
网络配置文件如下:# vi /etc/network/interface ... # The primary network interface auto enp0s3 iface enp0s3 inet dhcp auto enp0s8 iface enp0s8 inet static address 192.168.137.16 netmask 255.255.255.0 gateway 192.168.137.1
eth0使用dhcp,eth1使用static。eth0的实际网络如下:
# ifconfig enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 10.0.2.15 netmask 255.255.255.0 broadcast 10.0.2.255 inet6 fe80::a00:27ff:fe55:2858 prefixlen 64 scopeid 0x20<link> ether 08:00:27:55:28:58 txqueuelen 1000 (Ethernet) RX packets 6 bytes 1476 (1.4 KB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 33 bytes 3108 (3.1 KB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
打开其路由,才发现了问题。
# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.137.1 0.0.0.0 UG 0 0 0 enp0s8 10.0.2.0 0.0.0.0 255.255.255.0 U 0 0 0 enp0s3 192.168.137.0 0.0.0.0 255.255.255.0 U 0 0 0 enp0s8
enp0s8网卡成为了默认路由,这就导致其他路由不能匹配到的网段都会走enp0s8这个网卡,而我们实际上配置与外网连接的虚拟网卡是enp0s3,环境自然就连接不了外网了。我们可以尝试手动来删除现在的默认路由。
# route del default # route add default gw 10.0.2.2 dev enp0s3 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default gateway 0.0.0.0 UG 0 0 0 enp0s3 10.0.2.0 0.0.0.0 255.255.255.0 U 0 0 0 enp0s3 192.168.137.0 0.0.0.0 255.255.255.0 U 0 0 0 enp0s8
路由设置成功,OS也可以访问外网了。但这只是修改了本次的路由设置,OS重启后就失效了,因此我们需要将配置持久化。
持久化路由配置
我们将路由持久化设置在网络配置文件/etc/network/interfaces中。在网卡启动后添加对应的路由增删的代码,与route命令类似,只是在句首加上up即可。# vi /etc/network/interfaces ... auto enp0s3 iface enp0s3 inet dhcp up route add default gw 10.0.2.2 dev enp0s3 auto enp0s8 iface enp0s8 inet static address 192.168.137.16 netmask 255.255.255.0 gateway 192.168.137.1 up route del default dev enp0s8
注意:up route add default gw [gateway-addr] dev [dev-name],该语句中,[dev-name]表示外网网卡的名称,即上面的enp0s3,而[gateway-addr]表示外网网卡使用的网关ip地址。
那么,如何获取这个外网网卡的网关地址呢?virtualbox如下规定:
In NAT mode, the guest network interface is assigned to the IPv4 range 10.0.x.0/24 by default where x corresponds to the instance of the NAT interface +2. So x is 2 when there is only one NAT instance active. In that case the guest is assigned to the address 10.0.2.15, the gateway is set to 10.0.2.2 and the name server can be found at 10.0.2.3.
简单的说,就是如果第0个网卡是NAT网卡,那么其网段的第三个数字就0+2=2就是10.0.2.0,网关为10.0.2.2,name server则是10.0.2.3.以此类推。
参考:https://www.virtualbox.org/manual/ch09.html#changenat
相关文章推荐
- virtualbox虚拟机安装Ubuntu 16.04 - NAT模式下不能连接外网
- virtualbox虚拟机NAT模式下不能连接外网
- virtualbox虚拟机NAT模式下不能连接外网
- virtualbox虚拟机NAT模式下不能连接外网
- vmware中linux虚拟机使用NAT模式不能连接外网解决
- VMware虚拟机选择NAT模式无法连接外网的主要原因
- mac下连接VirtualBox虚拟机(NAT模式)
- VMware中解决ubuntu不能连接网络问题---NAT模式
- 公司内网,虚拟机使用NAT模式连接外网问题解决
- 虚拟机下运行linux通过nat模式与主机通信、与外网连接
- centos中NAT模式下静态IP连接外网
- VMWARE NAT模式下虚拟机集群节点无法连接外网问题解决
- Linux下配置(桥接模式和nat连接外网)
- centos中NAT模式下静态IP连接外网
- 虚拟机NAT模式设置连接外网
- Vmvare中NAT模式静态ip不能连外网的一种解决方法
- 使用NAT模式实现外网连接虚拟机的Web服务
- xshell远程连接工具不能连接本地刚安装的linux系统(网络模式选择“NAT模式”)
- SSH连接使用NAT模式的Virtualbox虚拟机
- 简单区分Vmware的三种网络连接模式(bridged、NAT、host_only)