Introducing Linux Network Namespaces
2016-03-05 20:29
761 查看
Introducing Linux Network Namespaces
4 September 2013In this post, I’m going to introduce you to the concept of Linux network namespaces. While it might seem a bit esoteric right now, trust me that there is a reason why I’m introducing you to network namespaces—if you, like me, are on a journey to better understand OpenStack, you’ll almost certainly run into network namespaces again.
So what are network namespaces? Generally speaking, an installation of Linux shares a single set of network interfaces and routing table entries. You can modify the routing table entries using policy routing (here’s an introduction I wrote and here’s a write-up on a potential use case for policy routing), but that doesn’t fundamentally change the fact that the set of network interfaces and routing tables/entries are shared across the entire OS. Network namespaces change that fundamental assumption. With network namespaces, you can have different and separate instances of network interfaces and routing tables that operate independent of each other.
This concept is probably best illustrated through some examples. Along the way, I’ll introduce a few new ideas as well. First, though, I need to provide some assumptions.
Assumptions
Throughout these examples, I’m using Ubuntu Server 12.04.3 LTS. Please note that support for network namespaces varies between Linux distributions; Ubuntu supports them but Red Hat doesn’t. (I’m not sure about Fedora. If you know, speak up in the comments.) If you’re thinking about using network namespaces, be sure your Linux distribution includes support.Further, I’ll assume that you’re either running as root, or that you will prepend
sudoto the commands listed here as necessary.
Creating and Listing Network Namespaces
Creating a network namespace is actually quite easy. Just use this command:ip netns add <new namespace name>For example, let’s say you wanted to create a namespace called “blue”. You’d use this command:
ip netns add blueTo verify that the network namespace has been created, use this command:
ip netns listYou should see your network namespace listed there, ready for you to use.
Assigning Interfaces to Network Namespaces
Creating the network namespace is only the beginning; the next part is to assign interfaces to the namespaces, and then configure those interfaces for network connectivity. One thing that threw me off early in my exploration of network namespaces was that you couldn’t assign physical interfaces to a namespace. How in the world were you supposed to use them, then?It turns out you can only assign virtual Ethernet (veth) interfaces to a network namespace. Virtual Ethernet interfaces are an interesting construct; they always come in pairs, and they are connected like a tube—whatever comes in one veth interface will come out the other peer veth interface. As a result, you can use veth interfaces to connect a network namespace to the outside world via the “default” or “global” namespace where physical interfaces exist.
Let’s see how that’s done. First, you’d create the veth pair:
ip link add veth0 type veth peer name veth1I found a few sites that repeated this command to create
veth1and link it to
veth0, but my tests showed that both interfaces were created and linked automatically using this command listed above. Naturally, you could substitute other names for
veth0and
veth1, if you wanted.
You can verify that the veth pair was created using this command:
ip link listYou should see a pair of veth interfaces (using the names you assigned in the command above) listed there. Right now, they both belong to the “default” or “global” namespace, along with the physical interfaces.
Let’s say that you want to connect the global namespace to the blue namespace. To do that, you’ll need to move one of the veth interfaces to the blue namespace using this command:
ip link set veth1 netns blueIf you then run the
ip link listcommand again, you’ll see that the veth1 interface has disappeared from the list. It’s now in the blue namespace, so to see it you’d need to run this command:
ip netns exec blue ip link listWhoa! That’s a bit of a complicated command. Let’s break it down:
The first part,
ip netns exec, is how you execute commands in a different network namespace.
Next is the specific namespace in which the command should be run (in this case, the blue namespace).
Finally, you have the actual command to be executed in the remote namespace. In this case, you want to see the interfaces in the blue namespace, so you run
ip link list.
When you run that command, you should see a loopback interface and the veth1 interface you moved over earlier.
Configuring Interfaces in Network Namespaces
Now that veth1 has been moved to the blue namespace, we need to actually configure that interface. Once again, we’ll use theip netns execcommand, this time to configure the veth1 interface in the blue namespace:
ip netns exec blue ifconfig veth1 10.1.1.1/24 upAs before, the format this command follows is:
ip netns exec <network namespace> <command to run against that namespace>In this case, you’re using
ifconfigto assign an IP address to the veth1 interface and bring that interface up. (Note: you could use the
ip addr,
ip route, and
ip linkcommands to accomplish the same thing.)
Once the veth1 interface is up, you can verify that the network configuration of the blue namespace is completely separate by just using a few different commands. For example, let’s assume that your “global” namespace has physical interfaces in the 172.16.1.0/24 range, and your veth1 interface is in a separate namespace and assigned something from the 10.1.1.0/24 range. You could verify how network namespaces keep the network configuration separate using these commands:
ip addr listin the global namespace will not show any 10.1.1.0/24-related interfaces or addresses.
ip netns exec blue ip addr listwill show only the 10.1.1.0/24-related interfaces and addresses, and will not show any interfaces or addresses from the global namespace.
Similarly,
ip route listin each namespace will show different routing table entries, including different default gateways.
Connecting Network Namespaces to the Physical Network
This part of it threw me for a while. I can’t really explain why, but it did. Once I’d figured it out, it was obvious. To connect a network namespace to the physical network, just use a bridge. In my case, I used an Open vSwitch (OVS) bridge, but a standard Linux bridge would work as well. Place one or more physical interfaces as well as one of the veth interfaces in the bridge, and—bam!—there you go. Naturally, if you had different namespaces, you’d probably want/need to connect them to different physical networks or different VLANs on the physical network.So there you go—an introduction to Linux network namespaces. It’s quite likely I’ll build on this content later, so while it seems a bit obscure right now just hang on to this knowledge. In the meantime, if you have questions, clarifications, or other information worth sharing with other readers, please feel free to speak up in the comments.
Tags: CLI · Linux · Networking Previous Post: Technology Short Take #35 Next Post: Vendor Meetings at VMworld 2013
Be social and share this post!
Recent Posts
Talking Containers, Virtualization, and Interop 16 Feb 2016
Technology Short Take #61 12 Feb 2016
Using KVM with Libvirt and macvtap Interfaces 09 Feb 2016
相关文章推荐
- Flex Namespace的用法
- JavaScript Archive Network 集合
- ajax使用不同namespace的action的方法
- thinkphp autoload 命名空间自定义 namespace
- PHP命名空间(namespace)的使用基础及示例
- php中namespace use用法实例分析
- C++ namespace相关语法实例分析
- PHP命名空间(Namespace)简明教程
- PHP命名空间(Namespace)的使用详解
- JavaScript创建命名空间(namespace)的最简实现
- ASP.Net中命名空间Namespace浅析和使用例子
- IEEE/ACM ASONAM 2014 Industry Track Call for Paper
- linux系统调优-Network
- C++ 匿名namespace的作用以及它与static的区别
- Android library listening network events.
- LINUN 网络连接小记
- 开源监控工具Hyperic 的 Network Device配置过程
- 修改 ESX Server IP 地址 常用命令
- Debian修改IP、DNS