ethtool 命令详解
2015-11-20 12:49
337 查看
命令描述:
ethtool 是用于查询及设置网卡参数的命令。
使用概要:
ethtool ethx //查询ethx网口基本设置,其中 x 是对应网卡的编号,如eth0、eth1等等
ethtool –h //显示ethtool的命令帮助(help)
ethtool –i ethX //查询ethX网口的相关信息
ethtool –d ethX //查询ethX网口注册性信息
ethtool –r ethX //重置ethX网口到自适应模式
ethtool –S ethX //查询ethX网口收发包统计
ethtool –s ethX [speed 10|100|1000] [duplex half|full] [autoneg on|off] //设置网口速率10/100/1000M、设置网口半/全双工、设置网口是否自协商
使用举例:
1)[root@linux /]# ethtool eth1
Settings for eth1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: umbg
Wake-on: d
Link detected: yes
2)[root@linux /]# ethtool -i eth1
driver: e1000
version: 5.0.43-k1
firmware-version: N/A
bus-info: 06:08.1
3)[root@linux /]# ethtool -S eth1
NIC statistics:
rx_packets: 58068300
tx_packets: 87124083
rx_bytes: 1589713008
tx_bytes: 2165825901
rx_errors: 0
tx_errors: 0
rx_dropped: 0
tx_dropped: 0
multicast: 0
collisions: 0
rx_length_errors: 0
rx_over_errors: 0
rx_crc_errors: 0
rx_frame_errors: 0
rx_fifo_errors: 0
rx_missed_errors: 0
tx_aborted_errors: 0
tx_carrier_errors: 0
tx_fifo_errors: 0
tx_heartbeat_errors: 0
tx_window_errors: 0
4)[root@linux /]# ethtool -s eth1 autoneg off speed 100 duplex full
相关参考:
1)[root@linux /]# which ethtool //查询 ethtool 存放的路径
/sbin/ethtool
2)[root@linux /]# rpm -qf /sbin/ethtool //查询 ethtool 的版本信息
ethtool-1.6-5
3)将 ethtool 设置永久保存在网络设备的方法
解决方法一:
ethtool 设置可通过 /etc/sysconfig/network-scripts/ifcfg-ethX 文件保存,从而在设备下次启动时激活选项。
例如:ethtool -s eth0 speed 100 duplex full autoneg off
此指令将eth0设备设置为全双工自适应,速度为100Mbs。若要eth0启动时设置这些参数, 修改文件/etc/sysconfig/network-scripts/ifcfg-eth0 ,添加如下一行:
ETHTOOL_OPTS="speed 100 duplex full autoneg off"
解决方法二:
将ethtool设置写入/etc/rc.d/rc.local之中。
命令描述:
ethtool 是用于查询及设置网卡参数的命令。
使用概要:
ethtool ethx //查询ethx网口基本设置,其中 x 是对应网卡的编号,如eth0、eth1等等
ethtool –h //显示ethtool的命令帮助(help)
ethtool –i ethX //查询ethX网口的相关信息
ethtool –d ethX //查询ethX网口注册性信息
ethtool –r ethX //重置ethX网口到自适应模式
ethtool –S ethX //查询ethX网口收发包统计
ethtool –s ethX [speed 10|100|1000] [duplex half|full] [autoneg on|off] //设置网口速率10/100/1000M、设置网口半/全双工、设置网口是否自协商
使用举例:
1)[root@linux /]# ethtool eth1
Settings for eth1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: umbg
Wake-on: d
Link detected: yes
2)[root@linux /]# ethtool -i eth1
driver: e1000
version: 5.0.43-k1
firmware-version: N/A
bus-info: 06:08.1
3)[root@linux /]# ethtool -S eth1
NIC statistics:
rx_packets: 58068300
tx_packets: 87124083
rx_bytes: 1589713008
tx_bytes: 2165825901
rx_errors: 0
tx_errors: 0
rx_dropped: 0
tx_dropped: 0
multicast: 0
collisions: 0
rx_length_errors: 0
rx_over_errors: 0
rx_crc_errors: 0
rx_frame_errors: 0
rx_fifo_errors: 0
rx_missed_errors: 0
tx_aborted_errors: 0
tx_carrier_errors: 0
tx_fifo_errors: 0
tx_heartbeat_errors: 0
tx_window_errors: 0
4)[root@linux /]# ethtool -s eth1 autoneg off speed 100 duplex full
相关参考:
1)[root@linux /]# which ethtool //查询 ethtool 存放的路径
/sbin/ethtool
2)[root@linux /]# rpm -qf /sbin/ethtool //查询 ethtool 的版本信息
ethtool-1.6-5
3)将 ethtool 设置永久保存在网络设备的方法
解决方法一:
ethtool 设置可通过 /etc/sysconfig/network-scripts/ifcfg-ethX 文件保存,从而在设备下次启动时激活选项。
例如:ethtool -s eth0 speed 100 duplex full autoneg off
此指令将eth0设备设置为全双工自适应,速度为100Mbs。若要eth0启动时设置这些参数, 修改文件/etc/sysconfig/network-scripts/ifcfg-eth0 ,添加如下一行:
ETHTOOL_OPTS="speed 100 duplex full autoneg off"
解决方法二:
将ethtool设置写入/etc/rc.d/rc.local之中。
相关文章推荐
- 【转】 android 4.4 Step Counter Sensor计步器的使用
- 游戏公会集体创业是中国玩家的悲哀
- Linux网络配置与远程连接
- Server.MapPath的用法
- swift2.1_Language Guide_Error Handling
- android-async-http下载框架
- 网上销售平台--OScache缓存(七)
- 比较大小的数时将第一个数设置为最大数或者最小数方法
- 【Leetcode】Reorder List
- Java线程池解析
- Linux命令大观
- Service 生命周期基础
- Universal-Image-Load开源框架1
- 手机QQ一键消除红点功能创造灵感
- IntelliJ IDEA 使用心得与常用快捷键
- 阶层上升的渠道
- masonry oc版( snapkit swift版)
- BZOJ1143[CTSC2008]祭祀river 偏序集及Dilworth定理
- 从sqlserver数据库中提取日期应该使用
- http request parameter