Xmanager Enterprise Linking VM Redhat Linux AS4.7 X64–Server Configuration

[root@localhost ~]# vi /etc/inittab

#
# inittab This file describes how the INIT process should set up
# the system in a certain run-level.
#
# Author: Miquel van Smoorenburg, <miquels@drinkel.nl.mugnet.org>
# Modified for RHS Linux by Marc Ewing and Donnie Barnes
#

# Default runlevel. The runlevels used by RHS are:
# 0 - halt (Do NOT set initdefault to this)
# 1 - Single user mode
# 2 - Multiuser, without NFS (The same as 3, if you do not have networking)
# 3 - Full multiuser mode
# 4 - unused
# 5 - X11
# 6 - reboot (Do NOT set initdefault to this)
#
id:5:initdefault:

# System initialization.
si::sysinit:/etc/rc.d/rc.sysinit

[root@localhost ~]# vi /etc/X11/gdm/gdm.conf

# The first form tells xdm which displays to respond to itself.
# The second form tells xdm to forward indirect queries from hosts matching
# the specified pattern to the indicated list of hosts.
# The third form tells xdm to handle indirect queries using the chooser;
# $XConsortium: Xaccess,v 1.5 91/08/26 11:52:51 rws Exp $
#
# Access control file for XDMCP connections
#
# To control Direct and Broadcast access:
#
# pattern
#
# To control Indirect queries:
#
# pattern list of hostnames and/or macros ...
#
# To use the chooser:
#
# pattern CHOOSER BROADCAST
#
# or
#
# pattern CHOOSER list of hostnames and/or macros ...
#
# To define macros:
#
# %name list of hosts ...
#
# XDMCP is the protocol that allows remote login. If you want to log into
# gdm remotely (I'd never turn this on on open network, use ssh for such
# remote usage that). You can then run X with -query <thishost> to log in,
# or -indirect <thishost> to run a chooser. Look for the 'Terminal' server
# type at the bottom of this config file.
[xdmcp]
# Distributions: Ship with this off. It is never a safe thing to leave
# out on the net. Setting up /etc/hosts.allow and /etc/hosts.deny to only
# allow local access is another alternative but not the safest.
# Firewalling port 177 is the safest if you wish to have xdmcp on.
# Read the manual for more notes on the security of XDMCP.
Enable=true
# Honour indirect queries, we run a chooser for these, and then redirect
# the user to the chosen host. Otherwise we just log the user in locally.
#HonorIndirect=true
# Maximum pending requests
#MaxPending=4
#MaxPendingIndirect=4
# Maximum open XDMCP sessions at any point in time
#MaxSessions=16
# Maximum wait times
#MaxWait=15
#MaxWaitIndirect=15
# How many times can a person log in from a single host. Usually better to
# keep low to fend off DoS attacks by running many logins from a single
# host. This is now set at 2 since if the server crashes then gdm doesn't
# know for some time and wouldn't allow another session.
#DisplaysPerHost=2
# The number of seconds after which a non-responsive session is logged off.
# Better keep this low.
#PingIntervalSeconds=15
# The port. 177 is the standard port so better keep it that way
Port=177

[root@localhost ~]# vi /etc/X11/xdm/xdm-config
! SECURITY: do not listen for XDMCP or Chooser requests
! Comment out this line if you want to manage X terminals with xdm
!DisplayManager.requestPort: 0

[root@localhost ~]# vi /etc/X11/xdm/Xaccess

# The first form tells xdm which displays to respond to itself.
# The second form tells xdm to forward indirect queries from hosts matching
# the specified pattern to the indicated list of hosts.
# The third form tells xdm to handle indirect queries using the chooser;
# the chooser is directed to send its own queries out via the broadcast
# address and display the results on the terminal.
# The fourth form is similar to the third, except instead of using the
# broadcast address, it sends DirectQuerys to each of the hosts in the list
#
# In all cases, xdm uses the first entry which matches the terminal;
# for IndirectQuery messages only entries with right hand sides can
# match, for Direct and Broadcast Query messages, only entries without
# right hand sides can match.
#

# * #any host can get a login window

#
# To hardwire a specific terminal to a specific host, you can
# leave the terminal sending indirect queries to this host, and
# use an entry of the form:
#

#terminal-a host-a

#
# The nicest way to run the chooser is to just ask it to broadcast
# requests to the network - that way new hosts show up automatically.
# Sometimes, however, the chooser can't figure out how to broadcast,
# so this may not work in all environments.
#

* CHOOSER BROADCAST #any indirect host can get a chooser