Centos 配置eth0 提示Device does not seem to be present
2015-10-22 23:11
597 查看
一.故障现象:
[root@c1node01 ~]# service network restart
Shutting down loopback insterface: [ OK ]
Bringing up loopback insterface: [ OK ]
Bringing up interface eth0: Device eth0 does not seem to be present,delaying initialization. [FAILED]
解决办法:
[root@c1node01 ~]# rm -rf /etc/udev/rules.d/70-persistent-net.rules
[root@c1node01 ~]# reboot ………………
[root@c1node01 ~]# service network restart
Shutting down loopback insterface: [ OK ]
Bringing up loopback insterface: [ OK ]
Bringing up interface eth0: [
OK ]
[root@c1node01 ~]#
二.另一种方法
造成这样的原因,是因为在虚拟机(Vmware)中移动了Centos系统对应的文件,导致重新配置时,网卡的MAC地址变了,输入ifconfig -a,找不到eth0
·······
安装完一个centos虚拟机,又拷贝一份,开机后网卡无法正常启动,报错:Device eth0 does not seem to be present,
delaying initialization
解决:# mv /etc/sysconfig/network-scripts/ifcfg-eth0
sysconfig/network-scripts/ifcfg-eth1
vim
sysconfig/network-scripts/ifcfg-eth1
修改DEVICE="eth0"
为DEVICE="eth1"
可删掉uuid、物理地址
然后重启启动网卡尝试下
三.比第一种更深入一点
故障前的操作:
DELL刀片装的是CentOS6.3的操作系统,网卡识别的是em1和em2,由于工作需要做了槽位调整,并启动了刀片
故障现象:
启动后网络不通,通过iDRAC登录后route查看缺省路由正常;
重启网络服务:
[root@nodeA ~]# service network restart Shutting down loopback insterface: [ OK ] Bringing up loopback insterface: [ OK ] Bringing up interface em1: Device em1 does not seem to be present,delaying initialization. [FAILED]
分析问题和解决:
之前在别的文章中我们提过70-persistent-net.rules文件,所以看了一下:
[root@nodeA ~]# vi /etc/udev/rules.d/70-persistent-net.rules
# This file was automatically generated by the /lib/udev/write_net_rules # program, run by the persistent-net-generator.rules rules file. # # You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.
# PCI device 0x14e4:0x163a (bnx2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1e", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"
# PCI device 0x14e4:0x163a (bnx2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1c", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
发现NAME的名称不正确,依次将上述红色字体中的eth0改为em1,eth1改为em2;
*切记:网卡编号由MAC地址大小决定,MAC越小网卡编号越小;
如下:
…………
# PCI device 0x14e4:0x163a (bnx2)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1e", ATTR{type}=="1", KERNEL=="eth*", NAME="em2"
# PCI device 0x14e4:0x163a (bnx2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1c", ATTR{type}=="1", KERNEL=="eth*", NAME="em1"
保存退出~!
[root@nodeA ~]#reboot
[root@c1node01 ~]# service network restart
Shutting down loopback insterface: [ OK ]
Bringing up loopback insterface: [ OK ]
Bringing up interface eth0: Device eth0 does not seem to be present,delaying initialization. [FAILED]
解决办法:
[root@c1node01 ~]# rm -rf /etc/udev/rules.d/70-persistent-net.rules
[root@c1node01 ~]# reboot ………………
[root@c1node01 ~]# service network restart
Shutting down loopback insterface: [ OK ]
Bringing up loopback insterface: [ OK ]
Bringing up interface eth0: [
OK ]
[root@c1node01 ~]#
二.另一种方法
造成这样的原因,是因为在虚拟机(Vmware)中移动了Centos系统对应的文件,导致重新配置时,网卡的MAC地址变了,输入ifconfig -a,找不到eth0
·······
安装完一个centos虚拟机,又拷贝一份,开机后网卡无法正常启动,报错:Device eth0 does not seem to be present,
delaying initialization
解决:# mv /etc/sysconfig/network-scripts/ifcfg-eth0
sysconfig/network-scripts/ifcfg-eth1
vim
sysconfig/network-scripts/ifcfg-eth1
修改DEVICE="eth0"
为DEVICE="eth1"
可删掉uuid、物理地址
然后重启启动网卡尝试下
三.比第一种更深入一点
故障前的操作:
DELL刀片装的是CentOS6.3的操作系统,网卡识别的是em1和em2,由于工作需要做了槽位调整,并启动了刀片
故障现象:
启动后网络不通,通过iDRAC登录后route查看缺省路由正常;
重启网络服务:
[root@nodeA ~]# service network restart Shutting down loopback insterface: [ OK ] Bringing up loopback insterface: [ OK ] Bringing up interface em1: Device em1 does not seem to be present,delaying initialization. [FAILED]
分析问题和解决:
之前在别的文章中我们提过70-persistent-net.rules文件,所以看了一下:
[root@nodeA ~]# vi /etc/udev/rules.d/70-persistent-net.rules
# This file was automatically generated by the /lib/udev/write_net_rules # program, run by the persistent-net-generator.rules rules file. # # You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.
# PCI device 0x14e4:0x163a (bnx2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1e", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"
# PCI device 0x14e4:0x163a (bnx2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1c", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
发现NAME的名称不正确,依次将上述红色字体中的eth0改为em1,eth1改为em2;
*切记:网卡编号由MAC地址大小决定,MAC越小网卡编号越小;
如下:
…………
# PCI device 0x14e4:0x163a (bnx2)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1e", ATTR{type}=="1", KERNEL=="eth*", NAME="em2"
# PCI device 0x14e4:0x163a (bnx2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1c", ATTR{type}=="1", KERNEL=="eth*", NAME="em1"
保存退出~!
[root@nodeA ~]#reboot
相关文章推荐
- Linux中硬连接(hard link)与软连接(symbolic link)的区别
- linux下autoscan, aclocal, autoconf, automake以及Makefile.am, Configure.in等文件和工具的使用
- CentOS下MYSQL数据库的安装
- CentOS6 Python CGI程序示例
- Linux/Ubuntu下的PPPoE拨号上网方法
- linux 下载安装 Scientific Toolworks Understand
- CentOS 6.5下JIRA安装部署
- Wolfram Mathematica 10.3 Windows / Linux / MacOsx
- 第 三 十 八 天:Linux 的 LVM 逻 辑 卷 管 理
- linux下lsof实现对误删文件的恢复
- linux中.config,makefile,kconfig
- 64位Linux编译cximage手记
- Linux安装mysql——源码安装
- Linux 循环遍历文件目录
- linux下使用yum安装mysql详解
- linux 批量修改文件后缀名
- 第三十八天:分区 -- Parte
- Linux下fork()函数
- Linux监控软件之 Zabbix
- Centos6.6安装简易桌面环境