linux定期执行shell
2014-06-13 09:55
148 查看
2950交换机
简明配置维护手册
中国思科培训网
目录
说明 3
产品特性 3
配置端口 4
配置一组端口 4
配置二层端口 6
配置端口速率及双工模式 6
端口描述 7
监控及维护端口 8
监控端口和控制器的状态 8
刷新、重置端口及计数器 10
关闭和打开端口 10
配置VLAN 11
理解VLAN 11
可支持的VLAN 12
配置正常范围的VLAN 12
生成、修改以太网VLAN 13
删除VLAN 14
将端口分配给一个VLAN 15
配置VLAN Trunks 16
使用STP实现负载均衡 19
配置Cluster 23
说明
本手册只包括日常使用的有关命令及特性,其它未涉及的命令及特性请参考英文的详细配置手册。产品特性
2950是只支持二层的交换机支持VLAN
· 到250 个VLAN
· 支持VLAN ID从1到4094( IEEE 802.1Q 标准)
· 支持ISL及IEEE 802.1Q封装
安全
· 支持IOS标准的密码保护
· 支持标准及扩展的访问列表来定义安全策略
· 支持基于VLAN的访问列表
监视
· 交换机LED指示端口状态
· SPAN及远端SPAN (RSPAN) 可以监视任何端口或VLAN的流量
· 内置支持四组的RMON监控功能(历史、统计、告警及事件)
配置端口
配置一组端口
命令 | 目的 | |
Step 1 | configure terminal | 进入配置状态 |
Step 2 | interface range {port-range} | 进入组配置状态 |
Step 3 | 可以使用平时的端口配置命令进行配置 | |
Step 4 | end | 退回 |
Step 5 | show interfaces [interface-id] | 验证配置 |
Step 6 | copy running-config startup-config | 保存 |
· 有效的组范围:
o vlan从1 到4094
o fastethernet 槽位/{first port} - {last port}, 槽位为0
o gigabitethernet槽位/{first port} - {last port},槽位为0
o port-channel port-channel-number - port-channel-number, port-channel号从1到64
· 端口号之间需要加入空格,如:interface range fastethernet 0/1 – 5 是有效的,而interface range fastethernet 0/1-5 是无效的.
· interface range 命令只能配置已经存在的interface vlan
· 所有在同一组的端口必须是相同类别的。
见以下例子:
Switch# configure terminal
Switch(config)# interface range fastethernet0/1 - 5
Switch(config-if-range)# no shutdown
Switch(config-if-range)#
*Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up
*Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up
*Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/4, changed state to up
*Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/5, changed state to up
*Oct 6 08:24:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/05,
changed state to up
*Oct 6 08:24:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed
state to up
*Oct 6 08:24:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed
state to up
以下的例子显示使用句号来配置不同类型端口的组:
Switch# configure terminal
Switch(config)# interface range fastethernet0/1 - 3, gigabitethernet0/1 - 2
Switch(config-if-range)# no shutdown
Switch(config-if-range)#
*Oct 6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Oct 6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up
*Oct 6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up
*Oct 6 08:29:28: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up
*Oct 6 08:29:28: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to up
*Oct 6 08:29:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/ 1,
changed state to up
*Oct 6 08:29:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/ 2,
changed state to up
*Oct 6 08:29:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/ 3,
changed state to up
配置二层端口
2950的所有端口缺省的端口都是二层口,如果此端口已经配置成三层端口的话,则需要用switchport来使其成为二层端口。配置端口速率及双工模式
可以配置快速以太口的速率为10/100Mbps及千兆以太口的速率为10/100/1000-Mbps; 但对于GBIC端口则不能配置速率及双工模式,有时可以配置nonegotiate,当需要联接不支持自适应的其它千兆端口时
命令 | 目的 | |
Step 1 | configure terminal | 进入配置状态. |
Step 2 | interface interface-id | 进入端口配置状态. |
Step 3 | speed {10 | 100 | 1000 | auto | nonegotiate} | 设置端口速率 注 1000 只工作在千兆口. GBIC模块只工作在1000 Mbps下. nonegotiate 只能在这些GBIC上用 1000BASE-SX, -LX, and -ZX GBIC. |
Step 4 | duplex {auto | full | half} | 设置全双工或半双工. |
Step 5 | end | 退出 |
Step 6 | show interfaces interface-id | 显示有关配置情况 |
Step 7 | copy running-config startup-config | 保存 |
Switch(config)# interface fastethernet0/3
Switch(config-if)# speed 10
Switch(config-if)# duplex half
端口描述
命令 | 目的 | |
Step 1 | configure terminal | 进入配置模式 |
Step 2 | interface interface-id | 进入要加入描述的端口 |
Step 3 | description string | 加入描述 (最多240个字符). |
Step 4 | end | 退回. |
Step 5 | show interfaces interface-id description or show running-config | 验证. |
Step 6 | copy running-config startup-config | 保存 |
This example shows how to add a description on Fast Ethernet interface 0/4 and to verify the description:
Switch# config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet0/4
Switch(config-if)# description Connects to Marketing
Switch(config-if)# end
Switch# show interfaces fastethernet0/4 description
Interface Status Protocol Description
Fa0/4 up down Connects to Marketing
监控及维护端口
监控端口和控制器的状态
主要命令见下表:Show Commands for Interfaces Command | 目的 |
show interfaces [interface-id] | 显示所有端口或某一端口的状态和配置. |
show interfaces interface-id status [err-disabled] | 显示一系列端口的状态或错误-关闭的状态 |
show interfaces [interface-id] switchport | 显示二层端口的状态,可以用来决定此口是否为二层或三层口。 |
show interfaces [interface-id] description | 显示端口描述 |
show running-config interface [interface-id] | 显示当前配置中的端口配置情况 |
show version | 显示软硬件等情况 |
Switch# show interfaces status
Port Name Status Vlan Duplex Speed Type
Gi0/1 connected routed a-full a-100 10/100/1000Base
TX
Gi0/2 wce server 20.20.2 disabled routed auto auto 10/100/1000Base TX
Gi0/3 ip wccp web-cache notconnect routed auto auto 10/100/1000Base TX
Gi0/4 notconnect routed auto auto 10/100/1000Base TX
Gi0/5 notconnect routed auto auto 10/100/1000Base TX
Gi0/6 disabled routed auto auto 10/100/1000Base TX
Gi0/7 disabled routed auto auto 10/100/1000Base TX
Gi0/8 disabled routed auto 100 10/100/1000Base TX
Gi0/9 notconnect routed auto auto 10/100/1000Base TX
Gi0/10 notconnect routed auto auto 10/100/1000Base TX
Gi0/11 disabled routed auto auto unknown
Gi0/12 notconnect routed auto auto unknown
Switch# show interfaces fastethernet 0/1 switchport
Name: Fa0/1
Switchport: Enabled
Administrative Mode: static access
Operational Mode: down
Administrative Trunking Encapsulation: dot1q
Negotiation of Trunking: Off
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Protected: false
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Voice VLAN: dot1p (Inactive)
Appliance trust: 5
Switch# show running-config interface fastethernet0/2
Building configuration...
Current configuration : 131 bytes
!
interface FastEthernet0/2
switchport mode access
switchport protected
no ip address
mls qos cos 7
mls qos cos override
end
刷新、重置端口及计数器
Clear命令 | 目的 |
clear counters [interface-id] | 清除端口计数器. |
clear line [number | console 0 | vty number] | 重置异步串口的硬件逻辑 |
Note clear counters 命令只清除用show interface所显示的计数,不影响用snmp得到的计数 |
Switch# clear counters fastethernet0/5
Clear "show interface" counters on this interface [confirm] y
Switch#
*Sep 30 08:42:55: %CLEAR-5-COUNTERS: Clear counter on interface FastEthernet0/5
by vty1 (171.69.115.10)
可使用clear line 命令来清除或重置某一端口或串口,在大部分情况下并不需要这样做:
Switch# clear interface fastethernet0/5
关闭和打开端口
命令 | 目的 | |
Step 1 | configure terminal | 进入配置状态 |
Step 2 | interface {vlan vlan-id} | {{fastethernet | gigabitethernet} interface-id} | {port-channel port-channel-number} | 选择要关闭的端口 |
Step 3 | shutdown | 关闭 |
Step 4 | end | 退出 |
Step 5 | show running-config | 验证 |
举例如下:
Switch# configure terminal
Switch(config)# interface fastethernet0/5
Switch(config-if)# shutdown
Switch(config-if)#
*Sep 30 08:33:47: %LINK-5-CHANGED: Interface FastEthernet0/5, changed state to a
administratively down
Switch# configure terminal
Switch(config)# interface fastethernet0/5
Switch(config-if)# no shutdown
Switch(config-if)#
*Sep 30 08:36:00: %LINK-3-UPDOWN: Interface FastEthernet0/5, changed state to up
配置VLAN
理解VLAN
一个VLAN就是一个交换网,其逻辑上按功能、项目、应用来分而不必考虑用户的物理位置。任何交换口都可以属于某一VLAN, IP包、广播包及组播包均可以发送或广播给在此VLAN内的最终用户。每一个VLAN均可看成是一个逻辑网络,发往另一VLAN的数据包必须由路由器或网桥转发(如下图)。由于VLAN被看成是一个逻辑网络,其具有自己的网桥管理信息庫 (MIB) 并可支持自己的生成树VLAN作为逻辑定义的网络示意图
VLAN常常与IP子网相联系,同一IP子网属于同一VLAN。在3550上VLAN之间的数据包可以由VLAN端口进行转发。
可支持的VLAN
Catalyst 3550交换机支持250个 VLAN,可以分别是VTP client, server, 及 transparent modes. VLAN号可以从1到4094. VLAN号1002到1005保留给令牌环及FDDI VLAN. VTP只能学习到普通范围的VLAN, 即从VLAN到1到1005; VLAN号大于1005属于扩展VLAN,不存在VLAN数据庫中。 交换机必须配置成VTP透明模式当需要生成VLAN 号从1006到4094.本交换机支持基于每一VLAN的生成树(PVST),最多支持128个生成树。本交换机支持ISL及IEEE 802.1Q trunk二种封装。
配置正常范围的VLAN
VLAN号1, 1002到1005是自动生成的不能被去掉。VLAN号1到1005的配置被写到文件vlan.dat 中, 可以用show vlan 命令查看, vlan.dat 文件存放在NVRAM中.
注意 不要手工删除vlan.dat 文件,可能造成VLAN的不完整。 如要删除vlan需要用有关的命令来进行 |
生成、修改以太网VLAN
命令 | 目的 | |
Step 1 | configure terminal | 进入配置状态 |
Step 2 | vlan vlan-id | 输入一个VLAN号, 然后进入vlan配置状态,可以输入一个新的VLAN号或旧的来进行修改。 |
Step 3 | name vlan-name | (可选)输入一个VLAN名,如果没有配置VLAN名,缺省的名字是VLAN号前面用0填满的4位数,如VLAN0004是VLAN4的缺省名字 |
Step 4 | mtu mtu-size | (可选) 改变MTU大小 |
Step 5 | end | 退出 |
Step 6 | show vlan {name vlan-name | id vlan-id} | 验证 |
Step 7 | copy running-config startup config | (可选) 保存配置 |
举例如下:
Switch# configure terminal
Switch(config)# vlan 20
Switch(config-vlan)# name test20
Switch(config-vlan)# end
也可以在enable状态下,进行VLAN配置:
命令 | 目的 | |
Step 1 | vlan database | 进入VLAN配置状态 |
Step 2 | vlan vlan-id name vlan-name | 加入VLAN号及VLAN名 |
Step 3 | vlan vlan-id mtu mtu-size | (可选) 修改MTU大小 |
Step 4 | exit | 更新VLAN数据庫并退出 |
Step 5 | show vlan {name vlan-name | id vlan-id} | 验证配置 |
Step 6 | copy running-config startup config | 保存配置(可选) |
Switch# vlan database
Switch(vlan)# vlan 20 name test20
Switch(vlan)# exit
APPLY completed.
Exiting....
Switch#
删除VLAN
当删除一个处于VTP服务器的交换机上删除VLAN时,则此VLAN将在所有相同VTP的交换机上删除。当在透明模式下删除时,只在当前交换机上删除。注意 当删除一个VLAN时,原来属于此VLAN的端口将处于非激活的状态,直到将其分配给某一VLAN。 |
命令 | 目的 | |
Step 1 | configure terminal | 进入配置状态 |
Step 2 | no vlan vlan-id | 删除某一VLAN. |
Step 3 | end | 退出 |
Step 4 | show vlan brief | 验证 |
Step 5 | copy running-config startup config | 保存 |
将端口分配给一个VLAN
命令 | 目的 | |
Step 1 | configure terminal | 进入配置状态 |
Step 2 | interface interface-id | 进入要分配的端口 |
Step 3 | switchport mode access | 定义二层口 |
Step 4 | switchport access vlan vlan-id | 把端口分配给某一VLAN |
Step 5 | end | 退出 |
Step 6 | show running-config interface interface-id | 验证端口的VLAN号 |
Step 7 | show interfaces interface-id switchport | 验证端口的管理模式和VLAN情况 |
Step 8 | copy running-config startup-config | 保存配置 |
举例如下:
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 2
Switch(config-if)# end
Switch#
配置VLAN Trunks
命令 | 目的 | |
Step 1 | configure terminal | 进入配置状态 |
Step 2 | interface interface-id | 进入端口配置状态 |
Step 3 | switchport mode {dynamic {auto | desirable} | trunk} | 配置二层trunk模式。 dynamic auto—自动协商是否成为trunk dynamic desirable—把端口设置为trunk如果对方端口是trunk, desirable, 或自动模式 trunk—设置端口为强制的trunk方式,而不理会对方端口是否为trunk |
Step 4 | switchport access vlan vlan-id | (可选) 指定一个缺省VLAN, 如果此端口不再是trunk |
Step 5 | switchport trunk native vlan vlan-id | 指定802.1Q native VLAN号 |
Step 6 | end | 退出 |
Step 7 | show interfaces interface-id switchport | 显示有关switchport 的配置 |
Step 8 | show interfaces interface-id trunk | 显示有关trunk的配置 |
Step 9 | copy running-config startup-config | 保存配置 |
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface fastethernet0/4
Switch(config-if)# switchport mode trunk
Switch(config-if)# end
定义trunk允许的VLAN
缺省情况下trunk允许所有的VLAN通过。可以使用 switchport trunk allowed vlan remove vlan-list 来去掉某一VLANCommand | Purpose | |
Step 1 | configure terminal | 进入配置状态 |
Step 2 | interface interface-id | 进入端口配置 |
Step 3 | switchport mode trunk | 配置二层口为trunk |
Step 4 | switchport trunk allowed vlan {add | all | except | remove} vlan-list | (可选) 配置trunk允许的VLAN. 使用add, all, except, remove关健字 |
Step 5 | end | 退出 |
Step 6 | show interfaces interface-id switchport | 验证VLAN配置情况. |
Step 7 | copy running-config startup-config | 保存配置 |
举例如下:
Switch(config)# interface fastethernet0/1
Switch(config-if)# switchport trunk allowed vlan remove 2
Switch(config-if)# end
配置Native VLAN(802.1q)
封装802.1q的trunk端口可以接受带有标签和不带标签的数据流,交换机向native vlan传送不带标签的数据流,缺省情况下native VLAN是1。命令 | 目的 | |
Step 1 | configure terminal | 进入配置状态 |
Step 2 | interface interface-id | 进入配置成802.1qtrunk的端口 |
Step 3 | switchport trunk native vlan vlan-id | 配置native VLAN号 |
Step 4 | end | 退出 |
Step 5 | show interfaces interface-id switchport | 验证native VLAN配置 |
Step 6 | copy running-config startup-config | 保存配置 |
使用STP实现负载均衡
负载均衡可以使用流量分流到其它平行的trunks上去. 交换机为了避免环路, STP通常是阻断所有端口交换机之间只留一条链路 。使用负载均衡后, 可以把不同VLAN的流量分配到不同的trunk上。可以通过配置STP端口权值STP路径值来实现负载均衡. 如果使用STP端口权值来配置那么二条负载均衡的trunk必须联同一交换机上。使用路径值则即可以联相同的交换机与可以联不同的交换机。
使用STP端口权值的负载均衡
当同一台交换机的二个口形成环路时, STP端口权值用来决定那个口是enable的,那个口是阻断的。 可以通过配置端口权值来决定二对trunk各走那些VLAN, 有较高权值的端口(数字较小的)vlan, 将处于转发状态,同一个VLAN在另一个trunk有较低的权值(数字较大)则将处在阻断状态。 即同一VLAN只在一个trunk上发送接受。基于端口权值的负载均衡示意图
trunk1将发送和接收VLAN8-10的数据,trunk2将发送和接收VLAN3-6的数据
配置如下:
Command | Purpose | |
Step 1 | configure terminal | 进入Switch 1配置状态 |
Step 2 | vtp domain domain-name | 配置VTP域 |
Step 3 | vtp server | 将Switch 1配置成VTP server. |
Step 4 | end | 退出 |
Step 5 | show vtp status | 验证VTP的配置 |
Step 6 | show vlan | 验证VLAN |
Step 7 | configure terminal | 进入配置状态 |
Step 8 | interface fastethernet 0/1 | 进入F0/1端口 |
Step 9 | switchport mode trunk | 配置成trunk端口 |
Step 10 | end | 退出 |
Step 11 | show interfaces fastethernet0/1 switchport | 验证VLAN配置 |
Step 12 | 在switch1上的F0/2上重复7到11步骤 | |
Step 13 | 在Switch 2的F0/1,F0/2上重复7到11步骤。 | |
Step 14 | show vlan | 当trunk已经起来,在switch2上验证已经学到相关的vlan配置 |
Step 15 | configure terminal | 在Switch 1上进入配置状态 |
Step 16 | interface fastethernet0/1 | 进入要配置的端口 |
Step 17 | spanning-tree vlan 8 port-priority 10 | 将端口权值10赋与VLAN 8. |
Step 18 | spanning-tree vlan 9 port-priority 10 | 将端口权值10赋与VLAN 9. |
Step 19 | spanning-tree vlan 10 port-priority 10 | 将端口权值10赋与VLAN 10. |
Step 20 | exit | 退回. |
Step 21 | interface fastethernet0/2 | 进入F0/2 |
Step 22 | spanning-tree vlan 3 port-priority 10 | 将端口权值10赋与VLAN 3. |
Step 23 | spanning-tree vlan 4 port-priority 10 | 将端口权值10赋与VLAN 4. |
Step 24 | spanning-tree vlan 5 port-priority 10 | 将端口权值10赋与VLAN 5. |
Step 25 | spanning-tree vlan 6 port-priority 10 | 将端口权值10赋与VLAN 10. |
Step 26 | end | 退出 |
Step 27 | show running-config | 验证配置 |
Step 28 | copy running-config startup-config | 保存配置 |
配置STP路径值的负载均衡
也可以通过配置配置STP路径值来实现负载均衡,如下图所示Trunk1走VLAN8-10,Trunk2走VLAN2-4
命令 | 目的 | |
Step 1 | configure terminal | 进入 Switch 1配置状态 |
Step 2 | interface fastethernet 0/1 | 进入F0/1 |
Step 3 | switchport mode trunk | 配置Trunk,只能是dot1q模式 |
Step 4 | exit | 退回 |
Step 5 | 在F0/2口上重复2-4步骤 | |
Step 6 | end | 退出 |
Step 7 | show running-config | 验证配置 |
Step 8 | show vlan | 验证switch1已经学到Vlan |
Step 9 | configure terminal | 进入配置状态 |
Step 10 | interface fastethernet 0/1 | 进入F0/1 |
Step 11 | spanning-tree vlan 2 cost 30 | 设置Vlan2生成树路径值为30 |
Step 12 | spanning-tree vlan 3 cost 30 | 设置Vlan3生成树路径值为30 |
Step 13 | spanning-tree vlan 4 cost 30 | 设置Vlan4生成树路径值为30 |
Step 14 | end | 退出 |
Step 15 | 在switch1的F0/2上重复9-11步骤设置VLAN8,9,10生成树路径值为30 | |
Step 16 | exit | 退出 |
Step 17 | show running-config | 验证配置 |
Step 18 | copy running-config startup-config | 保存配置 |
配置Cluster
以本工程一个例子说明,该例子是信息大厦主楼十楼四台2950交换机堆叠的例子。例子中,第一、二台管理vlan做hsrp,IP地址如图所示。1、STEP 1:配置Clust管理vlan,如将vlan 5作为管理vlan。
命令:
interface vlan 5
no shutdown
end
2、STEP 2:查看各台设备上管理vlan的MAC地址。
命令:
show interface vlan 5
结果:
ZL-10th -Floor-1中的MAC地址为:000a.f404.ad80
ZL-10th -Floor-2中的MAC地址为:000a.f404.a500
ZL-10th -Floor-3中的MAC地址为:000a.f404.ab80
ZL-10th -Floor-4中的MAC地址为:000a.f404.ac00
3、STEP 3:在第一台设备上的配置
命令:
cluster standby-group ZL-10th-Floor
由于要配置standby,所以该命令是配置standby组名
cluster enable ZL-10th-Floor 0
配置cluster名,该台机是主设备
cluster member 1 mac-address 000a.f404.a500
配置第二台堆叠设备的参数,硬件地址为管理vlan地址
cluster member 2 mac-address 000a.f404.ab80
配置第三台堆叠设备的参数
cluster member 3 mac-address 000a.f404.ac00
配置第四台堆叠设备的参数
interface vlan 5
ip address 132.107.77.74 255.255.255.128
standby 2 ip 132.107.77.73
standby 2 priority 110
standby 2 preempt delay sync 0
standby 2 name ZL-10th-Floor
上面几条命令是管理vlan里standby的配置
4、STEP 4:配置第二台堆叠设备
命令:
cluster standby-group ZL-10th-Floor
cluster member 0 mac-address 000a.f404.ad80
配置第一台堆叠设备参数
cluster member 2 mac-address 000a.f404.ab80
cluster member 3 mac-address 000a.f404.ac00
cluster commander-address 000a.f404.ad80 member 1 name ZL-10th-Floor
上面一条命令指明是第二台堆叠设备
interface Vlan5
ip address 132.107.77.75 255.255.255.128
standby 2 ip 132.107.77.73
standby 2 priority 100
standby 2 preempt delay sync 0
standby 2 name ZL-10th-Floor
配置standby参数
5、STEP 5:配置第三台堆叠设备
cluster commander-address 000a.f404.ad80 member 2 name ZL-10th-Floor
6、配置第四台堆叠设备
cluster commander-address 000a.f404.ad80 member 3 name ZL-10th-Floor
相关文章推荐
- linux定期执行shell脚本的方式
- linux shell和配置文件的执行顺序
- Linux_shell_后台执行命令
- linux 定时执行shell脚本
- linux 执行shell脚本的方式及一些区别
- 运用Shell命令的时候可以在控制台上输入linux命令去执行
- LINUX下用SHELL脚本执行带输入输出参数的ORACLE存储过程并得到结果
- java Windows下cmd 命令和Linux下shell命令 执行非JDK中的jar包
- Linux 任务定期执行
- Linux 中关于定期执行任务
- linux系统中shell中执行命令是报:bash: ifconfig: command not found错误的解决办法
- Linux_shell_命令执行的顺序
- Linux下使用Shell命令控制任务Jobs执行
- 从Linux程序中执行shell(程序、脚本)并获得输出结果
- linux执行java应用的shell
- 通过shell脚本定期删除linux用户下的日志
- linux 修改shell的执行文件路径
- 从Linux程序中执行shell(程序、脚本)并获得输出结果
- linux执行shell文件时遇到“指定文件不存在或未找到”
- linux 定时执行shell脚本详解