TQ2440 u-boot-2012.10移植二支持NAND启动
2013-09-26 17:52
197 查看
五一就要劳动，写点代码与大家分享哈哈。继 u-boot-2012.10移植一串口正常输出，继续修改代码支持单板NAND启动。最后直接用NOR Flash里的u-boot烧写自己移植的u-boot到NAND，方便电脑没有并口或手上没有openjtag,照样能移植u-boot，当然有openjtag更方便。
开发环境：
系统：ubuntu 10.04.4
单板：tq2440
NAND FLASH：K9F1216U0A 256MB
NOR Flash：AM29LV160A 2MB
SDRAM：HY57V561620 x2 64MB
NET：DM9000AEP
编译器：arm-2009q3-67-arm-none-linux-gnueabi-i686-pc-linux-gnu.tar.bz2
搭建开发环境详见ubuntu 10.04.4开发环境配置。
目标：
1.支持NOR Flash启动，串口正常输出
2.支持NAND启动
3.支持DM9000网卡
4.添加u-boot菜单
5.裁剪u-boot及制作补丁
NOR Flash是内存接口，能直接运行程序，但是NAND Flash地址线都没有，是不能直接跑程序的。熟悉三星片子的人都知道s3c2440 NAND启动时，CPU会自动从NAND Flash读取前4KB到SRAM,同时把这段片内SRAM映射到nGCS0片选空间即0x0000 0000。而ARM架构的CPU第一条指令是从0地址开始执行的。相当于片内SRAM充当一个载体，把NAND前4KB映射到0地址，CPU开始执行NAND前4KB内容。
change@change:~$ cd Si/TQ2440/u-boot-2012.10/
change@change:~/Si/TQ2440/u-boot-2012.10$ ls u-boot.bin -l
-rw-r--r-- 1 change change 368508 2013-04-30 21:49 u-boot.bin
change@change:~/Si/TQ2440/u-boot-2012.10$
看到生成的u-boot.bin有360KB左右，这个放在NOR Flash里能直接启动，但是不利于NAND启动。u-boot运行后，不管是NNAD还是NOR Flash启动，都会进行重定位，即把代码拷到内存运行，就像PC机一样程序都是在内存运行的。那么支持NAND启动的u-boot，重定位之前代码必须小于4KB，才能跑起来。分析现在较新的u-boot源码(以后在另外文章分析)，代码连接时加-pie选项，重定位成位置无关代码，搞的很高级，不利于像S3C2440这样片内SRAM十分有限的SOC跑。这里修改重定位代码，支持NAND启动。
1.去掉-pie选项，不需要附加“*(.rel*)”、“*(.dynsm)”等信息
change@change:~/Si/TQ2440/u-boot-2012.10$ grep "\-pie" * -nR
arch/x86/config.mk:43:LDFLAGS_FINAL += --gc-sections -pie
arch/arm/config.mk:88:LDFLAGS_u-boot += -pie
doc/README.arm-relocation:3:At arch level: add linker flag -pie
change@change:~/Si/TQ2440/u-boot-2012.10$ vim arch/arm/config.mk
去掉88行LDFLAGS_u-boot += -pie
2.参考以前update写的start.S init.c修改代码
在arch/arm/cpu/arm920t/start.S:205行增加如下代码
[plain] view
plaincopy
ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)/*sp =30000f80*/
bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
bl nand_init_ll
mov r0, #0
//ldr r1, =_start
ldr r1, _TEXT_BASE
//dr r2, =__bss_start
//sub r2, r2, r1
ldr r2, _bss_start_ofs
bl copy_code_to_sdram
bl clear_bss
ldr pc, =call_board_init_f
arch/arm/cpu/arm920t/start.S221：注释掉下面2行
//ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
//bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
在arch/arm/cpu/arm920t/start.S:226行增加如下代码
/*unsigned int id */
ldr r1, _TEXT_BASE//*link addres
ldr sp, base_sp
bl board_init_r//*the second step
用自己的重定位代码，去掉u-boot自带的arch/arm/cpu/arm920t/start.S 231：
[plain] view
plaincopy
/*------------------------------------------------------------------------------*/
/*
* void relocate_code (addr_sp, gd, addr_moni)
*
* This "function" does not return, instead it continues in RAM
* after relocating the monitor code.
*
*/
.globl relocate_code
relocate_code:
mov r4, r0 /* save addr_sp */
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
/* Set up the stack */
stack_setup:
mov sp, r4
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
beq clear_bss /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r1!, {r9-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end address [r2] */
blo copy_loop
#ifndef CONFIG_SPL_BUILD
/*
* fix .rel.dyn relocations
*/
ldr r0, _TEXT_BASE /* r0 <- Text base */
sub r9, r6, r0 /* r9 <- relocation offset */
ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
add r10, r10, r0 /* r10 <- sym table in FLASH */
ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
add r0, r0, r9 /* r0 <- location to fix up in RAM */
ldr r1, [r2, #4]
and r7, r1, #0xff
cmp r7, #23 /* relative fixup? */
beq fixrel
cmp r7, #2 /* absolute fixup? */
beq fixabs
/* ignore unknown type of fixup */
b fixnext
fixabs:
/* absolute fix: set location to (offset) symbol value */
mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
add r1, r10, r1 /* r1 <- address of symbol in table */
ldr r1, [r1, #4] /* r1 <- symbol value */
add r1, r1, r9 /* r1 <- relocated sym addr */
b fixnext
fixrel:
/* relative fix: increase location by offset */
ldr r1, [r0]
add r1, r1, r9
fixnext:
str r1, [r0]
add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
clear_bss:
#ifndef CONFIG_SPL_BUILD
ldr r0, _bss_start_ofs
ldr r1, _bss_end_ofs
mov r4, r6 /* reloc addr */
add r0, r0, r4
add r1, r1, r4
mov r2, #0x00000000 /* clear */
clbss_l:cmp r0, r1 /* clear loop... */
bhs clbss_e /* if reached end of bss, exit */
str r2, [r0]
add r0, r0, #4
b clbss_l
clbss_e:
bl coloured_LED_init
bl red_led_on
#endif
以上代码全部去掉，在之前已重定位
接着在board/samsung/TQ2440/目录下增加init.c文件，board/samsung/TQ2440/init.c:
[plain] view
plaincopy
/* NAND FLASH控制器 */
#define NFCONF (*((volatile unsigned long *)0x4E000000))
#define NFCONT (*((volatile unsigned long *)0x4E000004))
#define NFCMMD (*((volatile unsigned char *)0x4E000008))
#define NFADDR (*((volatile unsigned char *)0x4E00000C))
#define NFDATA (*((volatile unsigned char *)0x4E000010))
#define NFSTAT (*((volatile unsigned char *)0x4E000020))
/* GPIO */
#define GPHCON (*(volatile unsigned long *)0x56000070)
#define GPHUP (*(volatile unsigned long *)0x56000078)
/* UART registers*/
#define ULCON0 (*(volatile unsigned long *)0x50000000)
#define UCON0 (*(volatile unsigned long *)0x50000004)
#define UFCON0 (*(volatile unsigned long *)0x50000008)
#define UMCON0 (*(volatile unsigned long *)0x5000000c)
#define UTRSTAT0 (*(volatile unsigned long *)0x50000010)
#define UTXH0 (*(volatile unsigned char *)0x50000020)
#define URXH0 (*(volatile unsigned char *)0x50000024)
#define UBRDIV0 (*(volatile unsigned long *)0x50000028)
#define TXD0READY (1<<2)
void nand_read_ll(unsigned int addr, unsigned char *buf, unsigned int len);
static int isBootFromNorFlash(void)
{
volatile int *p = (volatile int *)0;
int val;
val = *p;
*p = 0x12345678;
if (*p == 0x12345678)
{
/* 写成功, 是nand启动 */
*p = val;
return 0;
}
else
{
/* NOR不能像内存一样写 */
return 1;
}
}
void copy_code_to_sdram(unsigned char *src, unsigned char *dest, unsigned int len)
{
int i = 0;
/* 如果是NOR启动 */
if (isBootFromNorFlash())
{
while (i < len)
{
dest[i] = src[i];
i++;
}
}
else
{
//nand_init();
nand_read_ll((unsigned int)src, dest, len);
}
}
void clear_bss(void)
{
extern int __bss_start, __bss_end__;
int *p = &__bss_start;
for (; p < &__bss_end__; p++)
*p = 0;
}
void nand_init_ll(void)
{
#define TACLS 0
#define TWRPH0 1
#define TWRPH1 0
/* 设置时序 */
NFCONF = (TACLS<<12)|(TWRPH0<<8)|(TWRPH1<<4);
/* 使能NAND Flash控制器, 初始化ECC, 禁止片选 */
NFCONT = (1<<4)|(1<<1)|(1<<0);
}
static void nand_select(void)
{
NFCONT &= ~(1<<1);
}
static void nand_deselect(void)
{
NFCONT |= (1<<1);
}
static void nand_cmd(unsigned char cmd)
{
volatile int i;
NFCMMD = cmd;
for (i = 0; i < 10; i++);
}
static void nand_addr(unsigned int addr)
{
unsigned int col = addr % 2048;
unsigned int page = addr / 2048;
volatile int i;
NFADDR = col & 0xff;
for (i = 0; i < 10; i++);
NFADDR = (col >> 8) & 0xff;
for (i = 0; i < 10; i++);
NFADDR = page & 0xff;
for (i = 0; i < 10; i++);
NFADDR = (page >> 8) & 0xff;
for (i = 0; i < 10; i++);
NFADDR = (page >> 16) & 0xff;
for (i = 0; i < 10; i++);
}
static void nand_wait_ready(void)
{
while (!(NFSTAT & 1));
}
static unsigned char nand_data(void)
{
return NFDATA;
}
void nand_read_ll(unsigned int addr, unsigned char *buf, unsigned int len)
{
int col = addr % 2048;
int i = 0;
/* 1. 选中 */
nand_select();
while (i < len)
{
/* 2. 发出读命令00h */
nand_cmd(0x00);
/* 3. 发出地址(分5步发出) */
nand_addr(addr);
/* 4. 发出读命令30h */
nand_cmd(0x30);
/* 5. 判断状态 */
nand_wait_ready();
/* 6. 读数据 */
for (; (col < 2048) && (i < len); col++)
{
buf[i] = nand_data();
i++;
addr++;
}
col = 0;
}
/* 7. 取消选中 */
nand_deselect();
}
同时修改该目录下的在Makfile,board/samsung/TQ2440/Makefile:
COBJS := smdk2410.o 改为 COBJS:= smdk2410.o init.o
其中lowlevel_init.S定义_TEXT_BASE: .word CONFIG_SYS_TEXT_BASE，是u-boot的重定位地址，搜索定义在TQ2440.h42:
//#define CONFIG_SYS_TEXT_BASE 0x0
#define CONFIG_SYS_TEXT_BASE 0x33f80000
arch/arm/lib/board.c274：增加extern ulong base_sp;//**add
arch/arm/lib/board.c448：修改如下
: base_sp = addr_sp;//**add
//relocate_code(addr_sp, id, addr);
return (unsigned int) id;// add it
arch/arm/lib/board.c382：修改如下
//addr -= gd->mon_len;
//addr &= ~(4096 - 1);
addr = _TEXT_BASE;//**add return sp to start.s
代码部分修改的差不多了，接下来还要修改链接脚本，确保重定位之前的代码编译在最前面
在arch/arm/cpu/u-boot.lds 38:增加如下
board/samsung/TQ2440/libTQ2440.o(.text)
3.重新配置、编译
change@change:~/Si/TQ2440/u-boot-2012.10$ make distclean
change@change:~/Si/TQ2440/u-boot-2012.10$ make TQ2440 CROSSS_COMPILE=arm-none-linux-gnueabi-
/bin/bash: arm-linux-gcc: command not found
make[1]: *** [lib/asm-offsets.s] Error 127
make[1]: Leaving directory `/home/change/Si/TQ2440/u-boot-2012.10'
make: *** [TQ2440] Error 2
老出现这个问题，我都指定编译器arm-none-linux-gnueabi- ，还是报/bin/bash: arm-linux-gcc: command not found，算啦换回arm-linux-gcc-4.3.2,并设置为默认交叉编译链，其它不变
change@change:~/Si/TQ2440/u-boot-2012.10$ make distclean
change@change:~/Si/TQ2440/u-boot-2012.10$ make TQ2440_config
Configuring for TQ2440 board...
change@change:~/Si/TQ2440/u-boot-2012.10$ make
start.S:228: Error: internal_relocation (type: OFFSET_IMM) not fixed up
make[1]: *** [start.o] Error 1
make[1]: Leaving directory `/home/change/Si/TQ2440/u-boot-2012.10/arch/arm/cpu/arm920t'
make: *** [arch/arm/cpu/arm920t/start.o] Error 2
有错误，说start.S:228有错误，打开忘记定义了，修改如下arch/arm/cpu/arm920t/start.S112：增加
.globl base_sp
base_sp:
.long 0
change@change:~/Si/TQ2440/u-boot-2012.10$ make
ok问题解决，编译通过，看看现在的u-boot.bin多大
change@change:~/Si/TQ2440/u-boot-2012.10$ la u-boot.bin -l
-rwxr-xr-x 1 change change 344336 2013-05-01 16:43 u-boot.bin
change@change:~/Si/TQ2440/u-boot-2012.10$ cp u-boot.bin /home/change/work/tftpboot/
4.烧写、测试
记住这里是烧到NAND，我用NOR Flash里的u-boot烧写，拨到NOR Flash启动，设置串口 115200 8 n 1
U-Boot 2012.04.01 (Oct 25 2012 - 22:47:25)
CPUID: 32440001
FCLK: 400 MHz
HCLK: 100 MHz
PCLK: 50 MHz
DRAM: 64 MiB
WARNING: Caches not enabled
Flash: 0 KB
NAND: 256 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: dm9000
Hit any key to stop autoboot: 0
SMDK2410 # set ipaddr 172.16.1.111
SMDK2410 # set gatewayip 172.16.1.1
SMDK2410 # set serverip 172.16.1.132
SMDK2410 # tftp 0x32000000 u-boot.bin
dm9000 i/o: 0x20000000, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 00:0c:29:4d:e4:f4
could not establish link
Using dm9000 device
TFTP from server 172.16.1.132; our IP address is 172.16.1.111
Filename 'u-boot.bin'.
Load address: 0x32000000
Loading: ########################
done
Bytes transferred = 344336 (54110 hex)
SMDK2410 # nand erase 0 0x80000
NAND erase: device 0 offset 0x0, size 0x80000
Erasing at 0x60000 -- 100% complete.
OK
SMDK2410 # nand write 0x32000000 0 0x80000
NAND write: device 0 offset 0x0, size 0x80000
524288 bytes written: OK
SMDK2410 #
单板断电，设为NAND启动，串口输出如下：
U-Boot 2012.10 (May 01 2013 - 17:20:57)
CPUID: 32440001
FCLK: 405.600 MHz
HCLK: 101.400 MHz
PCLK: 50.700 MHz
DRAM: 64 MiB
接着就卡死了，很奇怪的问题，先写到这吧，既然串口都有输出了，应该问题不大，下次再调调看。
发现问题了这个时钟不是配置的，有问题，先解决时钟问题。在board/samsung/tq2440/smdk2410.c去掉对时钟MPLL的配置76：
/* to reduce PLL lock time, adjust the LOCKTIME register */
//writel(0xFFFFFF, &clk_power->locktime);
/* configure MPLL */
//writel((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV,
// &clk_power->mpllcon);
同时增加打印语句。arch/arm/lib/board.c 447:增加
puts("board_init_f over!\n");
再次编译，烧写输出如下：
U-Boot 2012.10 (May 02 2013 - 15:12:15)
CPUID: 32440001
FCLK: 400 MHz
HCLK: 100 MHz
PCLK: 50 MHz
DRAM: 64 MiB
board_init_f over!
并且反复重启，时钟是正常了，还是有问题。细细看代码，调用u-boot第二阶段代码，需要出入参数id，但我们id是从board_init_f返回的，犯了个低级错误
arch/arm/lib/board.c 268:将void board_init_f(ulong bootflag)修改unsigned int board_init_f(ulong bootflag)
同时修改include/common.h 314：
void board_init_f (ulong) __attribute__ ((noreturn));
改为unsigned int board_init_f (ulong);
修改后编译OK，烧进去还是有问题，我再多加些打印语句试试。貌似问题有点怪了，加了打印语句发现bl board_init_r就没跳转过去，貌似运行完 board_init_f就卡死了。很郁闷，立即换成u-boot-2012.04.01移植一遍又没问题。再分析吧，哪位知道指点哈啊
http://blog.csdn.net/u010216127/article/details/8871525
开发环境：
系统：ubuntu 10.04.4
单板：tq2440
NAND FLASH：K9F1216U0A 256MB
NOR Flash：AM29LV160A 2MB
SDRAM：HY57V561620 x2 64MB
NET：DM9000AEP
编译器：arm-2009q3-67-arm-none-linux-gnueabi-i686-pc-linux-gnu.tar.bz2
搭建开发环境详见ubuntu 10.04.4开发环境配置。
目标：
1.支持NOR Flash启动，串口正常输出
2.支持NAND启动
3.支持DM9000网卡
4.添加u-boot菜单
5.裁剪u-boot及制作补丁
NOR Flash是内存接口，能直接运行程序，但是NAND Flash地址线都没有，是不能直接跑程序的。熟悉三星片子的人都知道s3c2440 NAND启动时，CPU会自动从NAND Flash读取前4KB到SRAM,同时把这段片内SRAM映射到nGCS0片选空间即0x0000 0000。而ARM架构的CPU第一条指令是从0地址开始执行的。相当于片内SRAM充当一个载体，把NAND前4KB映射到0地址，CPU开始执行NAND前4KB内容。
change@change:~$ cd Si/TQ2440/u-boot-2012.10/
change@change:~/Si/TQ2440/u-boot-2012.10$ ls u-boot.bin -l
-rw-r--r-- 1 change change 368508 2013-04-30 21:49 u-boot.bin
change@change:~/Si/TQ2440/u-boot-2012.10$
看到生成的u-boot.bin有360KB左右，这个放在NOR Flash里能直接启动，但是不利于NAND启动。u-boot运行后，不管是NNAD还是NOR Flash启动，都会进行重定位，即把代码拷到内存运行，就像PC机一样程序都是在内存运行的。那么支持NAND启动的u-boot，重定位之前代码必须小于4KB，才能跑起来。分析现在较新的u-boot源码(以后在另外文章分析)，代码连接时加-pie选项，重定位成位置无关代码，搞的很高级，不利于像S3C2440这样片内SRAM十分有限的SOC跑。这里修改重定位代码，支持NAND启动。
1.去掉-pie选项，不需要附加“*(.rel*)”、“*(.dynsm)”等信息
change@change:~/Si/TQ2440/u-boot-2012.10$ grep "\-pie" * -nR
arch/x86/config.mk:43:LDFLAGS_FINAL += --gc-sections -pie
arch/arm/config.mk:88:LDFLAGS_u-boot += -pie
doc/README.arm-relocation:3:At arch level: add linker flag -pie
change@change:~/Si/TQ2440/u-boot-2012.10$ vim arch/arm/config.mk
去掉88行LDFLAGS_u-boot += -pie
2.参考以前update写的start.S init.c修改代码
在arch/arm/cpu/arm920t/start.S:205行增加如下代码
[plain] view
plaincopy
ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)/*sp =30000f80*/
bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
bl nand_init_ll
mov r0, #0
//ldr r1, =_start
ldr r1, _TEXT_BASE
//dr r2, =__bss_start
//sub r2, r2, r1
ldr r2, _bss_start_ofs
bl copy_code_to_sdram
bl clear_bss
ldr pc, =call_board_init_f
arch/arm/cpu/arm920t/start.S221：注释掉下面2行
//ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
//bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
在arch/arm/cpu/arm920t/start.S:226行增加如下代码
/*unsigned int id */
ldr r1, _TEXT_BASE//*link addres
ldr sp, base_sp
bl board_init_r//*the second step
用自己的重定位代码，去掉u-boot自带的arch/arm/cpu/arm920t/start.S 231：
[plain] view
plaincopy
/*------------------------------------------------------------------------------*/
/*
* void relocate_code (addr_sp, gd, addr_moni)
*
* This "function" does not return, instead it continues in RAM
* after relocating the monitor code.
*
*/
.globl relocate_code
relocate_code:
mov r4, r0 /* save addr_sp */
mov r5, r1 /* save addr of gd */
mov r6, r2 /* save addr of destination */
/* Set up the stack */
stack_setup:
mov sp, r4
adr r0, _start
cmp r0, r6
moveq r9, #0 /* no relocation. relocation offset(r9) = 0 */
beq clear_bss /* skip relocation */
mov r1, r6 /* r1 <- scratch for copy_loop */
ldr r3, _bss_start_ofs
add r2, r0, r3 /* r2 <- source end address */
copy_loop:
ldmia r0!, {r9-r10} /* copy from source address [r0] */
stmia r1!, {r9-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end address [r2] */
blo copy_loop
#ifndef CONFIG_SPL_BUILD
/*
* fix .rel.dyn relocations
*/
ldr r0, _TEXT_BASE /* r0 <- Text base */
sub r9, r6, r0 /* r9 <- relocation offset */
ldr r10, _dynsym_start_ofs /* r10 <- sym table ofs */
add r10, r10, r0 /* r10 <- sym table in FLASH */
ldr r2, _rel_dyn_start_ofs /* r2 <- rel dyn start ofs */
add r2, r2, r0 /* r2 <- rel dyn start in FLASH */
ldr r3, _rel_dyn_end_ofs /* r3 <- rel dyn end ofs */
add r3, r3, r0 /* r3 <- rel dyn end in FLASH */
fixloop:
ldr r0, [r2] /* r0 <- location to fix up, IN FLASH! */
add r0, r0, r9 /* r0 <- location to fix up in RAM */
ldr r1, [r2, #4]
and r7, r1, #0xff
cmp r7, #23 /* relative fixup? */
beq fixrel
cmp r7, #2 /* absolute fixup? */
beq fixabs
/* ignore unknown type of fixup */
b fixnext
fixabs:
/* absolute fix: set location to (offset) symbol value */
mov r1, r1, LSR #4 /* r1 <- symbol index in .dynsym */
add r1, r10, r1 /* r1 <- address of symbol in table */
ldr r1, [r1, #4] /* r1 <- symbol value */
add r1, r1, r9 /* r1 <- relocated sym addr */
b fixnext
fixrel:
/* relative fix: increase location by offset */
ldr r1, [r0]
add r1, r1, r9
fixnext:
str r1, [r0]
add r2, r2, #8 /* each rel.dyn entry is 8 bytes */
cmp r2, r3
blo fixloop
#endif
clear_bss:
#ifndef CONFIG_SPL_BUILD
ldr r0, _bss_start_ofs
ldr r1, _bss_end_ofs
mov r4, r6 /* reloc addr */
add r0, r0, r4
add r1, r1, r4
mov r2, #0x00000000 /* clear */
clbss_l:cmp r0, r1 /* clear loop... */
bhs clbss_e /* if reached end of bss, exit */
str r2, [r0]
add r0, r0, #4
b clbss_l
clbss_e:
bl coloured_LED_init
bl red_led_on
#endif
以上代码全部去掉，在之前已重定位
接着在board/samsung/TQ2440/目录下增加init.c文件，board/samsung/TQ2440/init.c:
[plain] view
plaincopy
/* NAND FLASH控制器 */
#define NFCONF (*((volatile unsigned long *)0x4E000000))
#define NFCONT (*((volatile unsigned long *)0x4E000004))
#define NFCMMD (*((volatile unsigned char *)0x4E000008))
#define NFADDR (*((volatile unsigned char *)0x4E00000C))
#define NFDATA (*((volatile unsigned char *)0x4E000010))
#define NFSTAT (*((volatile unsigned char *)0x4E000020))
/* GPIO */
#define GPHCON (*(volatile unsigned long *)0x56000070)
#define GPHUP (*(volatile unsigned long *)0x56000078)
/* UART registers*/
#define ULCON0 (*(volatile unsigned long *)0x50000000)
#define UCON0 (*(volatile unsigned long *)0x50000004)
#define UFCON0 (*(volatile unsigned long *)0x50000008)
#define UMCON0 (*(volatile unsigned long *)0x5000000c)
#define UTRSTAT0 (*(volatile unsigned long *)0x50000010)
#define UTXH0 (*(volatile unsigned char *)0x50000020)
#define URXH0 (*(volatile unsigned char *)0x50000024)
#define UBRDIV0 (*(volatile unsigned long *)0x50000028)
#define TXD0READY (1<<2)
void nand_read_ll(unsigned int addr, unsigned char *buf, unsigned int len);
static int isBootFromNorFlash(void)
{
volatile int *p = (volatile int *)0;
int val;
val = *p;
*p = 0x12345678;
if (*p == 0x12345678)
{
/* 写成功, 是nand启动 */
*p = val;
return 0;
}
else
{
/* NOR不能像内存一样写 */
return 1;
}
}
void copy_code_to_sdram(unsigned char *src, unsigned char *dest, unsigned int len)
{
int i = 0;
/* 如果是NOR启动 */
if (isBootFromNorFlash())
{
while (i < len)
{
dest[i] = src[i];
i++;
}
}
else
{
//nand_init();
nand_read_ll((unsigned int)src, dest, len);
}
}
void clear_bss(void)
{
extern int __bss_start, __bss_end__;
int *p = &__bss_start;
for (; p < &__bss_end__; p++)
*p = 0;
}
void nand_init_ll(void)
{
#define TACLS 0
#define TWRPH0 1
#define TWRPH1 0
/* 设置时序 */
NFCONF = (TACLS<<12)|(TWRPH0<<8)|(TWRPH1<<4);
/* 使能NAND Flash控制器, 初始化ECC, 禁止片选 */
NFCONT = (1<<4)|(1<<1)|(1<<0);
}
static void nand_select(void)
{
NFCONT &= ~(1<<1);
}
static void nand_deselect(void)
{
NFCONT |= (1<<1);
}
static void nand_cmd(unsigned char cmd)
{
volatile int i;
NFCMMD = cmd;
for (i = 0; i < 10; i++);
}
static void nand_addr(unsigned int addr)
{
unsigned int col = addr % 2048;
unsigned int page = addr / 2048;
volatile int i;
NFADDR = col & 0xff;
for (i = 0; i < 10; i++);
NFADDR = (col >> 8) & 0xff;
for (i = 0; i < 10; i++);
NFADDR = page & 0xff;
for (i = 0; i < 10; i++);
NFADDR = (page >> 8) & 0xff;
for (i = 0; i < 10; i++);
NFADDR = (page >> 16) & 0xff;
for (i = 0; i < 10; i++);
}
static void nand_wait_ready(void)
{
while (!(NFSTAT & 1));
}
static unsigned char nand_data(void)
{
return NFDATA;
}
void nand_read_ll(unsigned int addr, unsigned char *buf, unsigned int len)
{
int col = addr % 2048;
int i = 0;
/* 1. 选中 */
nand_select();
while (i < len)
{
/* 2. 发出读命令00h */
nand_cmd(0x00);
/* 3. 发出地址(分5步发出) */
nand_addr(addr);
/* 4. 发出读命令30h */
nand_cmd(0x30);
/* 5. 判断状态 */
nand_wait_ready();
/* 6. 读数据 */
for (; (col < 2048) && (i < len); col++)
{
buf[i] = nand_data();
i++;
addr++;
}
col = 0;
}
/* 7. 取消选中 */
nand_deselect();
}
同时修改该目录下的在Makfile,board/samsung/TQ2440/Makefile:
COBJS := smdk2410.o 改为 COBJS:= smdk2410.o init.o
其中lowlevel_init.S定义_TEXT_BASE: .word CONFIG_SYS_TEXT_BASE，是u-boot的重定位地址，搜索定义在TQ2440.h42:
//#define CONFIG_SYS_TEXT_BASE 0x0
#define CONFIG_SYS_TEXT_BASE 0x33f80000
arch/arm/lib/board.c274：增加extern ulong base_sp;//**add
arch/arm/lib/board.c448：修改如下
: base_sp = addr_sp;//**add
//relocate_code(addr_sp, id, addr);
return (unsigned int) id;// add it
arch/arm/lib/board.c382：修改如下
//addr -= gd->mon_len;
//addr &= ~(4096 - 1);
addr = _TEXT_BASE;//**add return sp to start.s
代码部分修改的差不多了，接下来还要修改链接脚本，确保重定位之前的代码编译在最前面
在arch/arm/cpu/u-boot.lds 38:增加如下
board/samsung/TQ2440/libTQ2440.o(.text)
3.重新配置、编译
change@change:~/Si/TQ2440/u-boot-2012.10$ make distclean
change@change:~/Si/TQ2440/u-boot-2012.10$ make TQ2440 CROSSS_COMPILE=arm-none-linux-gnueabi-
/bin/bash: arm-linux-gcc: command not found
make[1]: *** [lib/asm-offsets.s] Error 127
make[1]: Leaving directory `/home/change/Si/TQ2440/u-boot-2012.10'
make: *** [TQ2440] Error 2
老出现这个问题，我都指定编译器arm-none-linux-gnueabi- ，还是报/bin/bash: arm-linux-gcc: command not found，算啦换回arm-linux-gcc-4.3.2,并设置为默认交叉编译链，其它不变
change@change:~/Si/TQ2440/u-boot-2012.10$ make distclean
change@change:~/Si/TQ2440/u-boot-2012.10$ make TQ2440_config
Configuring for TQ2440 board...
change@change:~/Si/TQ2440/u-boot-2012.10$ make
start.S:228: Error: internal_relocation (type: OFFSET_IMM) not fixed up
make[1]: *** [start.o] Error 1
make[1]: Leaving directory `/home/change/Si/TQ2440/u-boot-2012.10/arch/arm/cpu/arm920t'
make: *** [arch/arm/cpu/arm920t/start.o] Error 2
有错误，说start.S:228有错误，打开忘记定义了，修改如下arch/arm/cpu/arm920t/start.S112：增加
.globl base_sp
base_sp:
.long 0
change@change:~/Si/TQ2440/u-boot-2012.10$ make
ok问题解决，编译通过，看看现在的u-boot.bin多大
change@change:~/Si/TQ2440/u-boot-2012.10$ la u-boot.bin -l
-rwxr-xr-x 1 change change 344336 2013-05-01 16:43 u-boot.bin
change@change:~/Si/TQ2440/u-boot-2012.10$ cp u-boot.bin /home/change/work/tftpboot/
4.烧写、测试
记住这里是烧到NAND，我用NOR Flash里的u-boot烧写，拨到NOR Flash启动，设置串口 115200 8 n 1
U-Boot 2012.04.01 (Oct 25 2012 - 22:47:25)
CPUID: 32440001
FCLK: 400 MHz
HCLK: 100 MHz
PCLK: 50 MHz
DRAM: 64 MiB
WARNING: Caches not enabled
Flash: 0 KB
NAND: 256 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: dm9000
Hit any key to stop autoboot: 0
SMDK2410 # set ipaddr 172.16.1.111
SMDK2410 # set gatewayip 172.16.1.1
SMDK2410 # set serverip 172.16.1.132
SMDK2410 # tftp 0x32000000 u-boot.bin
dm9000 i/o: 0x20000000, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 00:0c:29:4d:e4:f4
could not establish link
Using dm9000 device
TFTP from server 172.16.1.132; our IP address is 172.16.1.111
Filename 'u-boot.bin'.
Load address: 0x32000000
Loading: ########################
done
Bytes transferred = 344336 (54110 hex)
SMDK2410 # nand erase 0 0x80000
NAND erase: device 0 offset 0x0, size 0x80000
Erasing at 0x60000 -- 100% complete.
OK
SMDK2410 # nand write 0x32000000 0 0x80000
NAND write: device 0 offset 0x0, size 0x80000
524288 bytes written: OK
SMDK2410 #
单板断电，设为NAND启动，串口输出如下：
U-Boot 2012.10 (May 01 2013 - 17:20:57)
CPUID: 32440001
FCLK: 405.600 MHz
HCLK: 101.400 MHz
PCLK: 50.700 MHz
DRAM: 64 MiB
接着就卡死了，很奇怪的问题，先写到这吧，既然串口都有输出了，应该问题不大，下次再调调看。
发现问题了这个时钟不是配置的，有问题，先解决时钟问题。在board/samsung/tq2440/smdk2410.c去掉对时钟MPLL的配置76：
/* to reduce PLL lock time, adjust the LOCKTIME register */
//writel(0xFFFFFF, &clk_power->locktime);
/* configure MPLL */
//writel((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV,
// &clk_power->mpllcon);
同时增加打印语句。arch/arm/lib/board.c 447:增加
puts("board_init_f over!\n");
再次编译，烧写输出如下：
U-Boot 2012.10 (May 02 2013 - 15:12:15)
CPUID: 32440001
FCLK: 400 MHz
HCLK: 100 MHz
PCLK: 50 MHz
DRAM: 64 MiB
board_init_f over!
并且反复重启，时钟是正常了，还是有问题。细细看代码，调用u-boot第二阶段代码，需要出入参数id，但我们id是从board_init_f返回的，犯了个低级错误
arch/arm/lib/board.c 268:将void board_init_f(ulong bootflag)修改unsigned int board_init_f(ulong bootflag)
同时修改include/common.h 314：
void board_init_f (ulong) __attribute__ ((noreturn));
改为unsigned int board_init_f (ulong);
修改后编译OK，烧进去还是有问题，我再多加些打印语句试试。貌似问题有点怪了，加了打印语句发现bl board_init_r就没跳转过去，貌似运行完 board_init_f就卡死了。很郁闷，立即换成u-boot-2012.04.01移植一遍又没问题。再分析吧，哪位知道指点哈啊
http://blog.csdn.net/u010216127/article/details/8871525
内容来自用户分享和网络整理，不保证内容的准确性，如有侵权内容，可联系管理员处理 
相关文章推荐
- TQ2440 u-boot-2012.10移植二支持NAND启动
- TQ2440 u-boot-2012.04.01移植二支持NAND启动
- u-boot-2009-11移植之stage1（支持从nand启动）
- 启动修改TQ2440 u-boot-2012.10移植一串口正常输出
- u-boot2010.03 移植篇(三)-----进一步修改start.S,smdk6410.h,支持nand启动及配置DM9000网卡
- u-boot2010.03 移植篇(二)-----修改start.S,支持nand启动
- 移植u-boot学习笔记5----- 修改代码之支持NAND启动
- u-boot-2012.04.01移植笔记——支持NAND启动
- u-boot-2011.03在TQ2440上的移植(3)--支持norflash启动 .
- u-boot-2012.04.01移植笔记——支持NAND启动
- u-boot2010.03 移植篇(二)-----修改start.S,支持nand启动 .
- u-boot2010.03 移植篇(二)-----修改start.S,支持nand启动
- u-boot2010.03 移植篇(二)-----修改start.S,支持nand启动
- u-boot-2011.03在TQ2440上的移植（5）—实现Nand/Nor 双启动
- u-boot-2010.06在TQ2440上的移植<4>--支持nandflash启动
- u-boot-2011.03在TQ2440上的移植(3)--支持norflash启动
- 【Linux 移植 】——4、移植 u-boot-2012.04.01 之 支持NAND启动
- u-boot-2011.03在TQ2440上的移植(4)--支持nandflash启动
- 移植u-boot-2012.04.01到jz2440开发板之修改代码支持NAND启动
- 移植u-boot2012.04.1 -》2440 (五)支持 nand nor 两种启动方式（完结）