在STM32上如果不使用外部晶振,OSC_IN和OSC_OUT的接法
2013-04-11 13:31
295 查看
如果使用内部RC振荡器而不使用外部晶振,请按照下面方法处理:
1)对于100脚或144脚的产品,OSC_IN应接地,OSC_OUT应悬空。
2)对于少于100脚的产品,有2种接法:
2.1)OSC_IN和OSC_OUT分别通过10K电阻接地。此方法可提高EMC性能。
2.2)分别重映射OSC_IN和OSC_OUT至PD0和PD1,再配置PD0和PD1为推挽输出并输出'0'。此方法可以减小功耗并(相对上面2.1)节省2个外部电阻。
以下是在ST英文网站FAQ上抄下的详细解释:
1) In 100 and 144 packages, the OSC_IN /OSC_Out pins are a dedicated pins for HSE and mapped respectively on pins 12, 13 and pins 23, 24 for
LQFP packages. Although, for BGA 100 and BGA 144 packages, they are mapped respectively on pins C1,D1 and pins D1,E1. In this case the recommended configuration is:
OSC_In pin must be connected to ground as it is always an input pin
OSC_Out must be left not connected as it is always an output pin.
2) In LQFP48 and LQFP64 packages, the OSC_IN/OSC_Out pins are mapped on pins 5,6 whereas in the VFQFPN36 package they are mapped on pins 2,3.
However the PD0 and PD1 functionality can be remapped by software on these pins. There are two possible configurations:
Hardware configuration: Connect the OSC_IN/OSC_Out pins to ground through a 10K pull down resistors.
Software configuration: First, the OSC_IN/OSC_Out pins are left not connected on PCB layout.
Then, remap the PD0 and PD1 functionality by software on these pins and configure the PD0/PD1 to Output push-pull forced to 0 logic level(Data Register = 0). This will maintain those I/Os to a fixed level minimizing Noise and external stress on these pins.
The software configuration is recommended to reduce the power consumption and saves cost by avoiding the use of external pull down resistors as
the I/O is already connected to the ground internally. Whereas the hardware configuration is recommended to increase the EMC performance.
1)对于100脚或144脚的产品,OSC_IN应接地,OSC_OUT应悬空。
2)对于少于100脚的产品,有2种接法:
2.1)OSC_IN和OSC_OUT分别通过10K电阻接地。此方法可提高EMC性能。
2.2)分别重映射OSC_IN和OSC_OUT至PD0和PD1,再配置PD0和PD1为推挽输出并输出'0'。此方法可以减小功耗并(相对上面2.1)节省2个外部电阻。
以下是在ST英文网站FAQ上抄下的详细解释:
1) In 100 and 144 packages, the OSC_IN /OSC_Out pins are a dedicated pins for HSE and mapped respectively on pins 12, 13 and pins 23, 24 for
LQFP packages. Although, for BGA 100 and BGA 144 packages, they are mapped respectively on pins C1,D1 and pins D1,E1. In this case the recommended configuration is:
OSC_In pin must be connected to ground as it is always an input pin
OSC_Out must be left not connected as it is always an output pin.
2) In LQFP48 and LQFP64 packages, the OSC_IN/OSC_Out pins are mapped on pins 5,6 whereas in the VFQFPN36 package they are mapped on pins 2,3.
However the PD0 and PD1 functionality can be remapped by software on these pins. There are two possible configurations:
Hardware configuration: Connect the OSC_IN/OSC_Out pins to ground through a 10K pull down resistors.
Software configuration: First, the OSC_IN/OSC_Out pins are left not connected on PCB layout.
Then, remap the PD0 and PD1 functionality by software on these pins and configure the PD0/PD1 to Output push-pull forced to 0 logic level(Data Register = 0). This will maintain those I/Os to a fixed level minimizing Noise and external stress on these pins.
The software configuration is recommended to reduce the power consumption and saves cost by avoiding the use of external pull down resistors as
the I/O is already connected to the ground internally. Whereas the hardware configuration is recommended to increase the EMC performance.
相关文章推荐
- 在STM32上如果不使用外部晶振,OSC_IN和OSC_OUT的接法
- 在STM32上如果不使用外部晶振,OSC_IN和OSC_OUT的接法
- STM32上不使用外部晶振,OSC_IN和OSC_OUT的接法
- STM32使用外部16MHZ晶振总结
- IAR下stm32使用12M外部晶振
- STM32不使用外部晶振的接法
- STM32使用内部晶振和外部晶振
- STM32使用16M外部晶振时串口乱码
- STM32 OSC_IN跟OSC_OUT的作用 和 各种接法
- STM32使用外部16MHZ晶振修改程序点
- stm32变更外部晶振时如何配置时钟、以及HSI的使用
- STM32使用外部16MHZ晶振总结
- STM32 OSC_IN和OSC_OUT的作用 和 各种接法
- 创建存储过程,以部门编号为参数返回该部门的人数及平均工资(返回一个值可以通过函数来实现,但如果要返回多个值,需要使用out或in out模式参数实现)
- STM32使用16M外部晶振时出现异常
- IAR下stm32使用12M外部晶振
- Verilog inout 双向口使用和仿真【转载】
- 同步复制使用系列一 Check In/Out
- MySQL 存储过程传參之in, out, inout 參数使用方法
- STM32 FSMC 外部使用SRAM