思科ASA防火墙8.4版本NAT的配置方法
2012-05-18 10:22
405 查看
mac-address-table aging-time
To configure the aging time for entries in the Layer 2 table, use the mac-address[/b]-table aging[/b]-time[/b] command in global configuration mode. To reset the seconds value to the default setting, use the no[/b] form of this command.Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
mac-address-table aging-time[/b] seconds
no mac-address-table aging-time[/b] seconds
Catalyst Switches
mac-address-table aging-time[/b] seconds [vlan[/b] vlan-id]
no mac-address-table aging-time [/b]seconds [vlan[/b] vlan-id]
Syntax Description
seconds | Aging time; valid values are 0, and from 10 to 1,000,000 seconds. |
vlan [/b]vlan-id | (Optional) Specifies the VLAN to apply the changed aging time; valid values are from 2 to 1001. |
Defaults
300 secondsCommand Modes
Global configurationCommand History
Release | Modification |
---|---|
12.0(7)XE | This command was introduced on Catalyst 6000 family switches. |
12.1(1)E | This command was implemented on Catalyst 6000 family switches. |
12.2(2)XT | This command was introduced on Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers. |
12.2(8)T | This command was integrated into Cisco IOS Release 12.2(8)T on Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers. |
12.2(11)T | This command was integrated into Cisco IOS Release 12.2(11)T. |
Usage Guidelines
Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series RoutersThe aging time entry will take the specified value. Valid entries are from 10 to 1,000,000 seconds.
This command cannot be disabled.
Catalyst Switches
If you do not enter a VLAN, the change is applied to all routed-port VLANs.
Enter 0 seconds to disable aging.
Examples
Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series RoutersThe following example shows the aging time being configured:
Router(config)# mac-address-table aging-time 300 [/b]
Catalyst Switches
The following example shows the aging time being configured:
Router(config)# mac-address-table aging-time 400 [/b]
The following example shows the aging time being disabled:
Router(config)# mac-address-table aging-time 0 [/b]
Related Commands
Command | Description |
---|---|
show mac[/b]-address[/b]-table aging[/b]-time[/b] | Displays the MAC address aging time. |
相关文章推荐
- 思科ASA防火墙8.4版本NAT的配置方法(转自新浪 刀光剑影)
- ASA防火墙 NAT新版老版的配置方法对比
- 思科ASA防火墙配置先进行NAT然后才是routing
- 思科ASA系列防火墙相关配置--8.4版
- 思科ASA防火墙之NAT
- 思科防火墙ASA配置案例 推荐
- 思科ASA防火墙配置手册
- ASA 防火墙nat配置
- 思科ASA系列防火墙相关配置--8.0版
- 如何配置双ISP备份借助思科ASA 5505防火墙
- ASA(8.X版本)防火墙配置实例
- 思科ASA防火墙配置
- 思科ASA防火墙配置
- 思科ASA防火墙基本配置之DNS刮出
- ASA8.4版本静态映射和PAT简单配置实验
- 思科ASA防火墙配置
- 如何配置双ISP备份借助思科ASA 5505防火墙