基于iscsi存储服务的搭建

创建新的分区：

[root@localhost /]# fdisk /dev/sdb

Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel

Building a new DOS disklabel. Changes will remain in memory only,

until you decide to write them. After that, of course, the previous

content won't be recoverable.

The number of cylinders for this disk is set to 13054.

There is nothing wrong with that, but this is larger than 1024,

and could in certain setups cause problems with:

1) software that runs at boot time (e.g., old versions of LILO)

2) booting and partitioning software from other OSs

(e.g., DOS FDISK, OS/2 FDISK)

Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)

Command (m for help): n

Command action

e extended

p primary partition (1-4)

p

Partition number (1-4): 1

First cylinder (1-13054, default 1):

Using default value 1

Last cylinder or +size or +sizeM or +sizeK (1-13054, default 13054):

Using default value 13054

Command (m for help):

Command (m for help): w

The partition table has been altered!

Calling ioctl() to re-read partition table.

WARNING: Re-reading the partition table failed with error 16: Device or resource busy.

The kernel still uses the old table.

The new table will be used at the next reboot.

Syncing disks.

[root@localhost /]# fdisk -l



Disk /dev/sda: 214.7 GB, 214748364800 bytes

255 heads, 63 sectors/track, 26108 cylinders

Units = cylinders of 16065 * 512 = 8225280 bytes

Device Boot Start End Blocks Id System

/dev/sda1 * 1 13 104391 83 Linux

/dev/sda2 14 26108 209608087+ 8e Linux LVM

Disk /dev/sdb: 107.3 GB, 107374182400 bytes

255 heads, 63 sectors/track, 13054 cylinders

Units = cylinders of 16065 * 512 = 8225280 bytes

Device Boot Start End Blocks Id System

/dev/sdb1 1 13054 104856223+ 83 Linux

2.搭建iscsi服务器

[root@localhost /]# yum -y install scsi-target-utils #安装软件包

开启服务

[root@localhost /]# /etc/init.d/tgtd start # 使用3260端口

Starting SCSI target daemon: Starting target framework daemon

c

[root@localhost /]# chkconfig tgtd on

详细信息可以man 一下 man tgtadm

下面创建一个存储（server）

# Create a target

tgtadm --lld iscsi --mode target --op new --tid 1 --targetname iqn.2007-03:virtual-dvd:'hostname'

# Create the SMC device and give it a nice name

tgtadm --lld iscsi --mode logicalunit --op new --tid 1 --lun 2 --backing-store /dev/sdb1

# Allow ALL initiators to connect to this target

tgtadm --lld iscsi --mode target --op bind --tid 1 --initiator-address ALL

# Show all our good work.

tgtadm --lld iscsi --mode target --op show

NOTE : 将上述需要写到rc.local文件中，开机自启动

挂载一个存储（client）

[root@it ~]# yum -y install iscsi-initiator-utils

可以man 一下 man iscsiadm

Discover targets at a given IP address:

iscsiadm --mode discoverydb --type sendtargets --portal 192.168.1.10 --discover

Login, must use a node record id found by the discovery:

iscsiadm --mode node --targetname iqn.2001-05.com.doe:test --portal 192.168.1.1:3260 --login

Logout:

iscsiadm --mode node --targetname iqn.2001-05.com.doe:test --portal 192.168.1.1:3260 --logout

List node records:

iscsiadm --mode node

Display all data for a given node record:

iscsiadm --mode node --targetname iqn.2001-05.com.doe:test --portal 192.168.1.1:3260

下面继续我的实例：

[root@it ~]# iscsiadm --mode discoverydb --type sendtargets --portal 192.168.7.116 --discover

192.168.7.116:3260,1 iqn.2007-03:virtual-dvd:hostname

[root@it ~]# iscsiadm --mode node --targetname iqn.2007-03:virtual-dvd:hostname --portal 192.168.7.116:3260 --login

Logging in to [iface: default, target: iqn.2007-03:virtual-dvd:hostname, portal: 192.168.7.116,3260]

Login to [iface: default, target: iqn.2007-03:virtual-dvd:hostname, portal: 192.168.7.116,3260] successful.

[root@it ~]# iscsiadm --mode node

192.168.7.116:3260,1 iqn.2007-03:virtual-dvd:hostname

[root@it ~]# fdisk -l

Disk /dev/sdc: 107.3 GB, 107372772864 bytes

255 heads, 63 sectors/track, 13053 cylinders

Units = cylinders of 16065 * 512 = 8225280 bytes

Disk /dev/sdc doesn't contain a valid partition table

多出来一个100G的硬盘 ， 这个就是之前挂载过来的那一快

之后进行格式化，挂载就可以了
本文出自 “Create One Eternal Love” 博客，转载请与作者联系！