CCNP路由实验---8、多区域的OSPF配置

一、实验目的
1、掌握OSPF协议的多区域配置
2、掌握OSPF协议的LSA类型
3、配置OSPF路由协议的汇总
二、实验拓扑





三、实验步骤
1、按照拓扑图配置好接口的IP地址和loopback网络，配置如下：
R1(config)#int s1/1
R1(config-if)#ip add 172.16.1.1 255.255.255.0
R1(config-if)#no shut
R1(config-if)#exit
R1(config)#int loop 0
R1(config-if)#ip add 172.16.64.1 255.255.255.0
R1(config-if)#exi
R1(config)#int loop 1
R1(config-if)#ip add 172.16.80.1 255.255.255.0
R1(config-if)#int loop 2
R1(config-if)#ip add 172.16.96.1 255.255.255.0
R1(config-if)#int loop 3
R1(config-if)#ip add 172.16.112.1 255.255.255.0
R1(config-if)#int loop 5
R1(config-if)#ip add 10.0.0.1 255.255.255.0
R1(config-if)#exit
其它R2、R3类似地配置好，并接口互相间直连要ping通。
2、同样地按照拓扑图配置多区域OSPF协议，配置如下
R1：
R1(config)#router ospf 1
R1(config-router)#network 172.16.1.0 0.0.0.255 area 0
R1(config-router)#network 172.16.64.0 0.0.0.255 area 1
R1(config-router)#network 172.16.80.0 0.0.0.255 area 1
R1(config-router)#network 172.16.96.0 0.0.0.255 area 1
R1(config-router)#network 172.16.112.0 0.0.0.255 area 1
R2、R3同样地配置好OSPF协议。
在R3[/b]配置如下网络到NULL0[/b]接口的静态路由，以便后面做OSPF[/b]外部路由实验时用到。[/b]
R3(config)#ip route 172.16.240.0 255.255.255.0 null 0
R3(config)#ip route 172.16.244.0 255.255.255.0 null 0
R3(config)#ip route 172.16.248.0 255.255.255.0 null 0
R3(config)#ip route 172.16.252.0 255.255.255.0 null 0
R3(config)#exit
3、配置好OSPF协议后，可以通过命令show ip ospf查看哪个路由器是ABR、哪个是ASBR。
R1#sh ip ospf
Routing Process "ospf 1" with ID 172.16.112.1[/b]
Supports only single TOS(TOS0) routes
Supports opaque LSA
Supports Link-local Signaling (LLS)
It is an area border router[/b]
Initial SPF schedule delay 5000 msecs
Minimum hold time between two consecutive SPFs 10000 msecs
Maximum wait time between two consecutive SPFs 10000 msecs
Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs
LSA group pacing timer 240 secs
Interface flood pacing timer 33 msecs
Retransmission pacing timer 66 msecs
Number of external LSA 0. Checksum Sum 0x000000
Number of opaque AS LSA 0. Checksum Sum 0x000000
Number of DCbitless external and opaque AS LSA 0
Number of DoNotAge external and opaque AS LSA 0
Number of areas in this router is 2. 2 normal 0 stub 0 nssa
External flood list length 0
Area BACKBONE(0)
Number of interfaces in this area is 1
Area has no authentication
SPF algorithm last executed 00:05:10.176 ago
SPF algorithm executed 9 times
Area ranges are
Number of LSA 7. Checksum Sum 0x02FB2B
Number of opaque link LSA 0. Checksum Sum 0x000000
Number of DCbitless LSA 0
Number of indication LSA 0
Number of DoNotAge LSA 0
Flood list length 0
Area 1
Number of interfaces in this area is 4 (4 loopback)
Area has no authentication
SPF algorithm last executed 00:06:46.200 ago
SPF algorithm executed 5 times
Area ranges are
Number of LSA 4. Checksum Sum 0x02490A
Number of opaque link LSA 0. Checksum Sum 0x000000
Number of DCbitless LSA 0
Number of indication LSA 0
Number of DoNotAge LSA 0
Flood list length 0
4、使用命令show ip ospf neighbor查看邻居信息。
R1#sh ip ospf nei

Neighbor ID Pri State Dead Time Address Interface
172.16.3.1 0 FULL/ - 00:00:35 172.16.1.2 Serial1/1

R2#sh ip ospf nei

Neighbor ID Pri State Dead Time Address Interface
172.16.112.1 0 FULL/ - 00:00:30 172.16.1.1 Serial1/0
172.16.224.2 0 FULL/ - 00:00:32 172.16.224.2 Serial1/2

R3#sh ip ospf nei

Neighbor ID Pri State Dead Time Address Interface
172.16.3.1 0 FULL/ - 00:00:32 172.16.224.1 Serial1/1
5、使用命令show ip route查看路由表。
R1#sh ip route

Gateway of last resort is not set

172.16.0.0/16 is variably subnetted, 7 subnets, 2 masks

O IA 172.16.224.0/24 [110/128] via 172.16.1.2, 00:10:12, Serial1/1[/b]
C 172.16.1.0/24 is directly connected, Serial1/1
O 172.16.3.1/32 [110/65] via 172.16.1.2, 00:10:12, Serial1/1
C 172.16.112.0/24 is directly connected, Loopback3
C 172.16.96.0/24 is directly connected, Loopback2
C 172.16.80.0/24 is directly connected, Loopback1
C 172.16.64.0/24 is directly connected, Loopback0
10.0.0.0/24 is subnetted, 1 subnets
C 10.0.0.0 is directly connected, Loopback5

R2#sh ip route

Gateway of last resort is not set

172.16.0.0/16 is variably subnetted, 7 subnets, 2 masks

C 172.16.224.0/24 is directly connected, Serial1/2
C 172.16.1.0/24 is directly connected, Serial1/0
C 172.16.3.0/24 is directly connected, Loopback0
O IA 172.16.112.1/32 [110/65] via 172.16.1.1, 00:09:50, Serial1/0[/b]
O IA 172.16.96.1/32 [110/65] via 172.16.1.1, 00:09:50, Serial1/0[/b]
O IA 172.16.80.1/32 [110/65] via 172.16.1.1, 00:09:50, Serial1/0[/b]
O IA 172.16.64.1/32 [110/65] via 172.16.1.1, 00:09:50, Serial1/0[/b]
[/b]
R3#sh ip route
Gateway of last resort is not set

172.16.0.0/16 is variably subnetted, 11 subnets, 2 masks
S 172.16.252.0/24 is directly connected, Null0
S 172.16.248.0/24 is directly connected, Null0
S 172.16.244.0/24 is directly connected, Null0
S 172.16.240.0/24 is directly connected, Null0
C 172.16.224.0/24 is directly connected, Serial1/1
O IA 172.16.1.0/24 [110/128] via 172.16.224.1, 00:06:19, Serial1/1[/b]
O IA 172.16.3.1/32 [110/65] via 172.16.224.1, 00:06:19, Serial1/1[/b]
O IA 172.16.112.1/32 [110/129] via 172.16.224.1, 00:06:19, Serial1/1[/b]
O IA 172.16.96.1/32 [110/129] via 172.16.224.1, 00:06:19, Serial1/1[/b]
O IA 172.16.80.1/32 [110/129] via 172.16.224.1, 00:06:19, Serial1/1[/b]
O IA 172.16.64.1/32 [110/129] via 172.16.224.1, 00:06:19, Serial1/1[/b]
加粗的都是区域间的路由。
6、为了减小路由表的条目，可以在R1上执行路由器汇总，配置如下：
R1(config)#router ospf 1
R1(config-router)#area 1 range 172.16.64.0 255.255.192.0
R1(config-router)#exit
配置好可以在R2、R3上查看路由表信息
R2#sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

172.16.0.0/16 is variably subnetted, 4 subnets, 2 masks
C 172.16.224.0/24 is directly connected, Serial1/2
C 172.16.1.0/24 is directly connected, Serial1/0
C 172.16.3.0/24 is directly connected, Loopback0
O IA 172.16.64.0/18 [110/65] via 172.16.1.1, 00:00:47, Serial1/0
对比前面的R2的路由表可以发现少了好多路由条目。
R3#sh ip route

Gateway of last resort is not set

172.16.0.0/16 is variably subnetted, 8 subnets, 3 masks
S 172.16.252.0/24 is directly connected, Null0
S 172.16.248.0/24 is directly connected, Null0
S 172.16.244.0/24 is directly connected, Null0
S 172.16.240.0/24 is directly connected, Null0
C 172.16.224.0/24 is directly connected, Serial1/1
O IA 172.16.1.0/24 [110/128] via 172.16.224.1, 00:14:16, Serial1/1
O IA 172.16.3.1/32 [110/65] via 172.16.224.1, 00:14:16, Serial1/1
O IA 172.16.64.0/18 [110/129] via 172.16.224.1, 00:00:10, Serial1/1
已经将R1通告过来的172.16.64.0~172.16.112.0网段都汇总成一条172.16.64.0/18的路由项了，大大地减少了路由条目。
7、R3必须重分布外部路由从外部网络172.16.240.0~172.16.252.0到OSPF的AS内部，配置如下：
R3(config)#router ospf 1
R3(config-router)#redistribute static
% Only classful networks will be redistributed // 不加上subnets只重发布classful路由
R3(config-router)#exit
R3(config)#router ospf 1
R3(config-router)#redistribute static subnets
R3(config-router)#exit
再分别在R1、R2上查看路由表
R1#sh ip route

Gateway of last resort is not set

172.16.0.0/16 is variably subnetted, 12 subnets, 3 masks
O E2 172.16.252.0/24 [110/20] via 172.16.1.2, 00:00:13, Serial1/1[/b]
O E2 172.16.248.0/24 [110/20] via 172.16.1.2, 00:00:13, Serial1/1[/b]
O E2 172.16.244.0/24 [110/20] via 172.16.1.2, 00:00:13, Serial1/1[/b]
O E2 172.16.240.0/24 [110/20] via 172.16.1.2, 00:00:13, Serial1/1[/b]
O IA 172.16.224.0/24 [110/128] via 172.16.1.2, 00:14:48, Serial1/1
C 172.16.1.0/24 is directly connected, Serial1/1
O 172.16.3.1/32 [110/65] via 172.16.1.2, 00:14:48, Serial1/1
C 172.16.112.0/24 is directly connected, Loopback3
C 172.16.96.0/24 is directly connected, Loopback2
C 172.16.80.0/24 is directly connected, Loopback1
C 172.16.64.0/24 is directly connected, Loopback0
O 172.16.64.0/18 is a summary, 00:14:48, Null0
10.0.0.0/24 is subnetted, 1 subnets
C 10.0.0.0 is directly connected, Loopback5

R2#sh ip route

Gateway of last resort is not set

172.16.0.0/16 is variably subnetted, 8 subnets, 2 masks
O E2 172.16.252.0/24 [110/20] via 172.16.224.2, 00:00:03, Serial1/2[/b]
O E2 172.16.248.0/24 [110/20] via 172.16.224.2, 00:00:02, Serial1/2[/b]
O E2 172.16.244.0/24 [110/20] via 172.16.224.2, 00:00:02, Serial1/2[/b]
O E2 172.16.240.0/24 [110/20] via 172.16.224.2, 00:00:02, Serial1/2[/b]
C 172.16.224.0/24 is directly connected, Serial1/2
C 172.16.1.0/24 is directly connected, Serial1/0
C 172.16.3.0/24 is directly connected, Loopback0
O IA 172.16.64.0/18 [110/65] via 172.16.1.1, 00:12:40, Serial1/0
这是因为对于外部路由[/b]OSPF[/b]默认使用[/b]E2[/b]类型的[/b]LSA,[/b]不计算[/b]AS[/b]内部路径所带来的[/b]cost[/b]值。[/b]
现在重新在R3上配置重分布，使用E1类型的LSA来计算看看。
R3(config)#router ospf 1
R3(config-router)#redistribute static metric-type 1 subnets
R3(config-router)#exit
配置完成后，分别使用show ip route[/b]查看R1、R2上的路由表。
R1#sh ip route

Gateway of last resort is not set

172.16.0.0/16 is variably subnetted, 12 subnets, 3 masks
O E1 172.16.252.0/24 [110/148] via 172.16.1.2, 00:00:23, Serial1/1[/b]
O E1 172.16.248.0/24 [110/148] via 172.16.1.2, 00:00:23, Serial1/1[/b]
O E1 172.16.244.0/24 [110/148] via 172.16.1.2, 00:00:23, Serial1/1[/b]
O E1 172.16.240.0/24 [110/148] via 172.16.1.2, 00:00:23, Serial1/1[/b]
O IA 172.16.224.0/24 [110/128] via 172.16.1.2, 00:12:23, Serial1/1
C 172.16.1.0/24 is directly connected, Serial1/1
O 172.16.3.1/32 [110/65] via 172.16.1.2, 00:12:23, Serial1/1
C 172.16.112.0/24 is directly connected, Loopback3
C 172.16.96.0/24 is directly connected, Loopback2
C 172.16.80.0/24 is directly connected, Loopback1
C 172.16.64.0/24 is directly connected, Loopback0
O 172.16.64.0/18 is a summary, 00:12:23, Null0
10.0.0.0/24 is subnetted, 1 subnets
C 10.0.0.0 is directly connected, Loopback5

R2#sh ip route

Gateway of last resort is not set

172.16.0.0/16 is variably subnetted, 8 subnets, 2 masks
O E1 172.16.252.0/24 [110/84] via 172.16.224.2, 00:02:05, Serial1/2[/b]
O E1 172.16.248.0/24 [110/84] via 172.16.224.2, 00:02:05, Serial1/2[/b]
O E1 172.16.244.0/24 [110/84] via 172.16.224.2, 00:02:05, Serial1/2[/b]
O E1 172.16.240.0/24 [110/84] via 172.16.224.2, 00:02:05, Serial1/2[/b]
C 172.16.224.0/24 is directly connected, Serial1/2
C 172.16.1.0/24 is directly connected, Serial1/0
C 172.16.3.0/24 is directly connected, Loopback0
O IA 172.16.64.0/18 [110/65] via 172.16.1.1, 00:12:08, Serial1/0
分别出现了4条E1类型的OSPF路由，R1和R2上相同目的网络的metric值不同，原因是把AS内部路径的cost值加进来了。如果在OSPF区域内只有一个出口，可以使用E2类型，如果区域有2个出口，我们可以用E1类型，以避免次优路径用来转发数据。本文出自 “孤帆远影碧空尽” 博客，请务必保留此出处http://bennie.blog.51cto.com/192876/423384