cisco3500系列交换机密码恢复
2010-03-20 21:14
302 查看
3500系列交换机密码恢复
1.拔掉交换机的电源线
2。用超级终端和控制线连到交换机,超级终端的设置是:
9600 baud rate
No parity
8 data bits
1 stop bit
No flow control
3。按住交换机前面板的“mode”按钮,插上电源线,当端口1上面的灯不亮后,放松“mode”按钮;
4。这时超级终端上应该显示:
The system has been interrupted prior to initializing the flash file
system.
The following commands will initialize the flash file system, and
finish loading
the operating system software:
flash_init
load_helper
boot
5。输入flash_init
6。输入load_helper
7. 输入dir flash:
这时显示:
Directory of flash:
2 -rwx 843947 Mar 01 1993 00:02:18 C2900XL-h-mz-112.8-SA
4 drwx 3776 Mar 01 1993 01:23:24 html
66 -rwx 130 Jan 01 1970 00:01:19 env_vars
68 -rwx 1296 Mar 01 1993 06:55:51 config.text
1728000 bytes total (456704 bytes free)
8。输入rename flash:config.text flash:config.old
9.输入boot,重新启动系统
10。系统启动完后显示:Continue with the configuration dialog? [yes/no] :
输入N
11.输入enable
12.进入enable模式后,输入rename flash:config.old flash:config.text
13。接着按以下步骤操作:
Switch# copy flash:config.text system:running-config
Source filename [config.text]? (press Return)
Destination filename [running-config]? (press Return)
14 。接着按以下步骤操作:
switch#configure terminal
switch(config)#no enable secret
switch(config)#no enable password
switch(config)#exit
switch#write memory
这时,系统就恢复没有密码的状态了
1.拔掉交换机的电源线
2。用超级终端和控制线连到交换机,超级终端的设置是:
9600 baud rate
No parity
8 data bits
1 stop bit
No flow control
3。按住交换机前面板的“mode”按钮,插上电源线,当端口1上面的灯不亮后,放松“mode”按钮;
4。这时超级终端上应该显示:
The system has been interrupted prior to initializing the flash file
system.
The following commands will initialize the flash file system, and
finish loading
the operating system software:
flash_init
load_helper
boot
5。输入flash_init
6。输入load_helper
7. 输入dir flash:
这时显示:
Directory of flash:
2 -rwx 843947 Mar 01 1993 00:02:18 C2900XL-h-mz-112.8-SA
4 drwx 3776 Mar 01 1993 01:23:24 html
66 -rwx 130 Jan 01 1970 00:01:19 env_vars
68 -rwx 1296 Mar 01 1993 06:55:51 config.text
1728000 bytes total (456704 bytes free)
8。输入rename flash:config.text flash:config.old
9.输入boot,重新启动系统
10。系统启动完后显示:Continue with the configuration dialog? [yes/no] :
输入N
11.输入enable
12.进入enable模式后,输入rename flash:config.old flash:config.text
13。接着按以下步骤操作:
Switch# copy flash:config.text system:running-config
Source filename [config.text]? (press Return)
Destination filename [running-config]? (press Return)
14 。接着按以下步骤操作:
switch#configure terminal
switch(config)#no enable secret
switch(config)#no enable password
switch(config)#exit
switch#write memory
这时,系统就恢复没有密码的状态了
相关文章推荐
- Catalyst 6500系列交换机密码恢复
- H3C系列交换机密码恢复方法
- 3500系列交换机密码恢复
- 一、Catalyst 2950系列交换机密码恢复
- 2950系列交换机密码恢复过程
- Cisco Catalyst 6500系列交换机密码恢复和启动问题总结
- 中兴交换机密码恢复
- Open-E DSS V7 应用系列之八 远程访问和管理员密码恢复
- 思科2600系列路由器的enable密码恢复
- 锐捷交换机密码恢复
- Cisco Catalyst交换机密码恢复策略
- 华为交换机密码恢复
- [转] 恢复交换机 密码
- 思科6509交换机密码恢复过程及注意事项!
- Cisco系列路由器密码恢复研究与实践
- 忆龙2009:恢复H3C系列交换机控制台登陆口令
- Cisco 2950 交换机恢复密码
- 锐捷交换机密码恢复(1)
- 路由器 交换机密码恢复
- 交换机密码恢复