Cisco路由器交换机配置命令详解(1)
2010-01-26 15:47
483 查看
1. 交换机支持的命令:
交换机基本状态:
交换机口令设置:
交换机VLAN设置:
交换机设置IP地址:
交换机显示命令:
2. 路由器支持的命令:
路由器显示命令:
路由器口令设置:
路由器配置:
路由器文件操作:
静态路由:
动态路由:
交换机基本状态:
switch: ;ROM状态, 路由器是rommon> hostname> ;用户模式 hostname# ;特权模式 hostname(config)# ;全局配置模式 hostname(config-if)# ;接口状态 |
switch>enable ;进入特权模式 switch#config terminal ;进入全局配置模式 switch(config)#hostname ;设置交换机的主机名 switch(config)#enable secret xxx ;设置特权加密口令 switch(config)#enable password xxa ;设置特权非密口令 switch(config)#line console 0 ;进入控制台口 switch(config-line)#line vty 0 4 ;进入虚拟终端 switch(config-line)#login ;允许登录 switch(config-line)#password xx ;设置登录口令xx switch#exit ;返回命令 |
switch#vlan database ;进入VLAN设置 switch(vlan)#vlan 2 ;建VLAN 2 switch(vlan)#no vlan 2 ;删vlan 2 switch(config)#int f0/1 ;进入端口1 switch(config-if)#switchport access vlan 2 ;当前端口加入vlan 2 switch(config-if)#switchport mode trunk ;设置为干线 switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlan switch(config-if)#switchport trunk encap dot1q ;设置vlan 中继 switch(config)#vtp domain ;设置发vtp域名 switch(config)#vtp password ;设置发vtp密码 switch(config)#vtp mode server ;设置发vtp模式 switch(config)#vtp mode client ;设置发vtp模式 |
switch(config)#interface vlan 1 ;进入vlan 1 switch(config-if)#ip address ;设置IP地址 switch(config)#ip default-gateway ;设置默认网关 switch#dir flash: ;查看闪存 |
switch#write ;保存配置信息 switch#show vtp ;查看vtp配置信息 switch#show run ;查看当前配置信息 switch#show vlan ;查看vlan配置信息 switch#show interface ;查看端口信息 switch#show int f0/0 ;查看指定端口信息 |
路由器显示命令:
router#show run ;显示配置信息 router#show interface ;显示接口信息 router#show ip route ;显示路由信息 router#show cdp nei ;显示邻居信息 router#reload ;重新起动 |
router>enable ;进入特权模式 router#config terminal ;进入全局配置模式 router(config)#hostname ;设置交换机的主机名 router(config)#enable secret xxx ;设置特权加密口令 router(config)#enable password xxb ;设置特权非密口令 router(config)#line console 0 ;进入控制台口 router(config-line)#line vty 0 4 ;进入虚拟终端 router(config-line)#login ;要求口令验证 router(config-line)#password xx ;设置登录口令xx router(config)#(Ctrl+z) ; 返回特权模式 router#exit ;返回命令 |
router(config)#int s0/0 ;进入Serail接口 router(config-if)#no shutdown ;激活当前接口 router(config-if)#clock rate 64000 ;设置同步时钟 router(config-if)#ip address ;设置IP地址 router(config-if)#ip address second ;设置第二个IP router(config-if)#int f0/0.1 ;进入子接口 router(config-subif.1)#ip address ;设置子接口IP router(config-subif.1)#encapsulation dot1q ;绑定vlan中继协议 router(config)#config-register 0x2142 ;跳过配置文件 router(config)#config-register 0x2102 ;正常使用配置文件 router#reload ;重新引导 |
router#copy running-config startup-config ;保存配置 router#copy running-config tftp ;保存配置到tftp router#copy startup-config tftp ;开机配置存到tftp router#copy tftp flash: ;下传文件到flash router#copy tftp startup-config;下载配置文件 ROM状态: Ctrl+Break ;进入ROM监控状态 rommon>confreg 0x2142 ;跳过配置文件 rommon>confreg 0x2102 ;恢复配置文件 rommon>reset ;重新引导 rommon>copy xmodem: flash: ;从console传输文件 rommon>IP_ADDRESS=10.65.1.2 ;设置路由器IP rommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码 rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP服务器IP rommon>TFTP_FILE=c2600.bin ;指定下载的文件 rommon>tftpdnld ;从tftp下载 rommon>dir flash: ;查看闪存内容 rommon>boot ;引导IOS |
ip route ;命令格式 router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例 router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例 |
router(config)#ip routing ;启动路由转发 router(config)#router rip ;启动RIP路由协议。 router(config-router)#network ;设置发布路由 router(config-router)#negihbor ;点对点帧中继用。 |
相关文章推荐
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解(1)
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解(1)
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解(整理粗稿集)
- Cisco路由器交换机配置命令详解
- Cisco 路由器交换机 配置命令详解
- Cisco路由器交换机配置命令详解(续)
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解
- Cisco 路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解
- Cisco路由器交换机配置命令详解 2