Visual Studio 2010 Beta2特性之office开发
2010-01-11 15:55
381 查看
实验拓朴:
实验目标:
目标1. 按照实验要求连接拓扑
目标2. 配置VTP域：SWITCH1、SWITCH2为VTP SERVER并开启VLTP修剪；SWITCH3、SWITCH4为VTP CLIENT；并在SERVER上创建VLAN2、3、4
目标3. 将SWITCH1配置为VLAN1、VLAN3的根桥，VLAN2、VLAN4的次根桥
将SWITCH2配置为VLAN2、VLAN4的根桥，VLAN1、VLAN3的次根桥
目标4. 在VTP CLIENT上将接口配置进正确的VLAN
目标5. 配置SWITCH1和SWITCH2之间的以太网通道
目标6. 在SWITCH1、SWITCH2、ROUTER1上配置RIP路由协议
目标7. 测试网络联通性：VLAN内PC连通性；VLAN间PC连通性；VLAN内PC与INTERNET连通性
实验步骤:
目标1:
1.搭环境.
Router1 E0/0 <----> Switch1 F0/0
Router1 E0/1 <----> Switch2 F0/0
Switch1 F0/14 <----> Switch2 F0/14
Switch1 F0/15 <----> Switch2 F0/15
Switch1 F0/1 <----> Switch3 F0/1
Switch1 F0/2 <----> Switch4 F0/1
Switch1 F0/3 <----> Switch5 F0/1
Switch2 F0/1 <----> Switch3 F0/2
Switch2 F0/2 <----> Switch4 F0/2
Switch2 F0/3 <----> Switch5 F0/2
Switch3 F0/14 <----> VPCS V0/1
Switch3 F0/15 <----> VPCS V0/2
Switch4 F0/14 <----> VPCS V0/3
Switch4 F0/15 <----> VPCS V0/4
Switch5 F0/14 <----> VPCS V0/5
Switch5 F0/15 <----> VPCS V0/6
2.R1相关配置:
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#interface e0/0
R1(config-if)#ip add 10.1.1.1 255.255.255.0
R1(config-if)#no sh
R1(config)#interface e0/1
R1(config-if)#ip add 10.1.2.1 255.255.255.0
R1(config-if)#no sh
R1(config-if)#exit
R1(config)#
R1#show ip in br
Interface IP-Address OK? Method Status Protocol
Ethernet0/0 10.1.1.1 YES manual up up
Ethernet0/1 10.1.2.1 YES manual up up
Ethernet0/2 unassigned YES unset administratively down down
Ethernet0/3 unassigned YES unset administratively down down
Loopback0 202.16.2.1 YES manual up up
R1#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
C 202.16.2.0/24 is directly connected, Loopback0
10.0.0.0/24 is subnetted, 2 subnets
C 10.1.2.0 is directly connected, Ethernet0/1
C 10.1.1.0 is directly connected, Ethernet0/0
目标2:
配置VTP域：SWITCH1、SWITCH2为VTP SERVER并开启VLTP修 剪；SWITCH3、SWITCH4，5为VTP CLIENT；并在SERVER上创建VLAN2、 3、4
1．sw1-3(config)#interface ra （trunk）
sw1-3(config)#interface range f0/0 - 3
sw1-3(config-if-range)#switchport mode trunk
sw1-3(config-if-range)#no sh
sw1-3(config-if-range)#exit
sw1-3(config)#interface range f0/14 - 15
sw1-3(config-if-range)#switchport mode trunk
sw1-3(config-if-range)#no sh
2．sw1-3#show interfaces switchp (test trunk)
Name: Fa0/0
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/2
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/3
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/14
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/15
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
3. SW2-3上面配置TRUNK 和SW1-3 同样的过程。（详细过程略）
4．sw3(config)#interface ra f0/1 -2 （TRUNK）
sw3(config-if-range)#switchport mode trunk
sw3(config-if-range)#no sh
sw3#show interfaces switchport
Name: Fa0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/2
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Applianc
5. sw4(config)#interface range f0/1 -2
sw4(config-if-range)#switchport mode trunk
sw4(config-if-range)#no sh
sw4(config-if-range)#exit
sw4(config)#exit
sw5(config)#interface range f0/1 -2
sw5(config-if-range)#switchport mode trunk
sw5(config-if-range)#no sh
6. sw1-3# vl da (start vtp)
sw1-3(vlan)#vtp domain test
Changing VTP domain name from NULL to test
sw1-3(vlan)#vtp server
Device mode already VTP SERVER.
sw1-3(vlan)#vtp password 111111
Setting device VLAN database password to 111111.
sw1-3(vlan)#vtp v2-mode
V2 mode enabled.
sw1-3(vlan)#vtp pruning
Pruning switched ON
sw1-3(vlan)#exit
APPLY completed.
Exiting....
sw1-3#show vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Server
VTP Domain Name : test
VTP Pruning Mode : Enabled
VTP V2 Mode : Enabled
VTP Traps Generation : Disabled
MD5 digest : 0xEE 0x18 0x41 0xD1 0x2B 0xFB 0x4F 0x52
Configuration last modified by 0.0.0.0 at 3-1-02 00:49:43
Local updater ID is 0.0.0.0 (no valid interface found)
sw1-3#
7. sw2-3#vl da (start vtp)
sw2-3(vlan)#vtp domain test
Changing VTP domain name from test\ to test
sw2-3(vlan)#vtp server
Device mode already VTP SERVER.
sw2-3(vlan)#vtp password 111111
Setting device VLAN database password to 111111.
sw2-3(vlan)#vtp v2-mode
V2 mode enabled.
sw2-3(vlan)#vtp pruning
Pruning switched ON
sw2-3(vlan)#exit
APPLY completed.
Exiting....
sw2-3#show vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Server
VTP Domain Name : test
VTP Pruning Mode : Enabled
VTP V2 Mode : Enabled
VTP Traps Generation : Disabled
MD5 digest : 0x7A 0x2A 0x67 0xAE 0x1E 0xBE 0x30 0x0E
Configuration last modified by 0.0.0.0 at 3-1-02 00:52:44
Local updater ID is 0.0.0.0 (no valid interface found)
sw2-3#
8. sw3#vl da (start vtp client)
sw3(vlan)#vtp domain test
Domain name already set to test .
sw3(vlan)#vtp client
Setting device to VTP CLIENT mode.
sw3(vlan)#vtp password 111111
Setting device VLAN database password to 111111.
sw3(vlan)#exit
In CLIENT state, no apply attempted.
Exiting....
sw3#show vtp st
sw3#show vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Client
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x05 0xFC 0x00 0x59 0x49 0xAF 0x1D 0xE2
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
sw4#vl da (start vtp client)
sw4(vlan)#vtp domain test
Domain name already set to test .
sw4(vlan)#vtp client
Setting device to VTP CLIENT mode.
sw4(vlan)#vtp password 111111
Setting device VLAN database password to 111111.
sw4(vlan)#exit
In CLIENT state, no apply attempted.
Exiting....
sw4#show vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Client
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x05 0xFC 0x00 0x59 0x49 0xAF 0x1D 0xE2
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
sw4#
sw5#vl da (start vtp client)
sw5(vlan)#vtp domain test
Domain name already set to test .
sw5(vlan)#vtp client
Setting device to VTP CLIENT mode.
sw5(vlan)#vtp password 111111
Setting device VLAN database password to 111111.
sw5(vlan)#exit
In CLIENT state, no apply attempted.
Exiting....
sw5#show vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Client
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x05 0xFC 0x00 0x59 0x49 0xAF 0x1D 0xE2
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
sw5#
9. sw1-3#vl da (create vlan 2,3,4.)
sw1-3(vlan)#vlan 2 name v2
VLAN 2 added:
Name: v2
sw1-3(vlan)#apply
APPLY completed.
sw1-3(vlan)#vlan 3 name v3
VLAN 3 added:
Name: v3
sw1-3(vlan)#apply
APPLY completed.
sw1-3(vlan)#vlan 4 name v4
VLAN 4 added:
Name: v4
sw1-3(vlan)#apply
APPLY completed.
sw1-3(vlan)#exit
APPLY completed.
Exiting....
sw1-3#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/4, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13
2 v2 active
3 v3 active
4 v4 active
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
10.client test
sw2-3#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/4, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13
2 v2 active
3 v3 active
4 v4 active
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
sw3#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15
2 v2 active
3 v3 active
4 v4 active
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
sw4#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15
2 v2 active
3 v3 active
4 v4 active
sw5#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15
2 v2 active
3 v3 active
4 v4 active
目标3:
将SWITCH1配置为VLAN1、VLAN3的根桥，VLAN2、VLAN4的次根桥
将SWITCH2配置为VLAN2、VLAN4的根桥，VLAN1、VLAN3的次根桥
1. sw1-3#conf t (config stp)
sw1-3(config)#spanning-tree vlan 1 root primary
% This switch is already the root of VLAN1 spanning tree
VLAN 1 bridge priority set to 8192
VLAN 1 bridge max aging time unchanged at 20
VLAN 1 bridge hello time unchanged at 2
VLAN 1 bridge forward delay unchanged at 15
sw1-3(config)#spanning-tree vlan 3 root primary
% This switch is already the root of VLAN3 spanning tree
VLAN 3 bridge priority set to 8192
VLAN 3 bridge max aging time unchanged at 20
VLAN 3 bridge hello time unchanged at 2
VLAN 3 bridge forward delay unchanged at 15
sw1-3(config)#spanning-tree vlan 2 root secondary
VLAN 2 bridge priority set to 16384
VLAN 2 bridge max aging time unchanged at 20
VLAN 2 bridge hello time unchanged at 2
VLAN 2 bridge forward delay unchanged at 15
sw1-3(config)#spanning-tree vlan 4 root secondary
VLAN 4 bridge priority set to 16384
VLAN 4 bridge max aging time unchanged at 20
VLAN 4 bridge hello time unchanged at 2
VLAN 4 bridge forward delay unchanged at 15
.
sw1-3#show spanning-tree br
VLAN1
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0000
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 8192
Address cc00.00f8.0000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/0 128.1 128 19 FWD 0 8192 cc00.00f8.0000 128.1
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0000 128.2
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.00f8.0000 128.3
FastEthernet0/3 128.4 128 19 FWD 0 8192 cc00.00f8.0000 128.4
FastEthernet0/14 128.15 128 19 FWD 0 8192 cc00.00f8.0000 128.15
FastEthernet0/15 128.16 128 19 FWD 0 8192 cc00.00f8.0000 128.16
--More―
2. sw2-3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
sw2-3(config)#spanning-tree vlan 2 root primary
VLAN 2 bridge priority set to 8192
VLAN 2 bridge max aging time unchanged at 20
VLAN 2 bridge hello time unchanged at 2
VLAN 2 bridge forward delay unchanged at 15
sw2-3(config)#spanning-tree vlan 4 root primary
VLAN 4 bridge priority set to 8192
VLAN 4 bridge max aging time unchanged at 20
VLAN 4 bridge hello time unchanged at 2
VLAN 4 bridge forward delay unchanged at 15
sw2-3(config)#spanning-tree vlan 1 root secondary
VLAN 1 bridge priority set to 16384
VLAN 1 bridge max aging time unchanged at 20
VLAN 1 bridge hello time unchanged at 2
VLAN 1 bridge forward delay unchanged at 15
sw2-3(config)#spanning-tree vlan 3 root secondary
VLAN 3 bridge priority set to 16384
VLAN 3 bridge max aging time unchanged at 20
VLAN 3 bridge hello time unchanged at 2
VLAN 3 bridge forward delay unchanged at 15
3. w4#show spanning-tree br (test stp )
VLAN1
Spanning enabled protocol ieee
Root ID Priority 81 92
Address cc00.00f8.0000
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0000 128.3
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0000 128.3
FastEthernet0/14 128.15 128 19 FWD 19 32768 cc00.058c.0000 128.15
FastEthernet0/15 128.16 128 19 FWD 19 32768 cc00.058c.0000 128.16
VLAN2
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0001
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0001
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0001 128.3
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0001 128.3
VLAN3
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0002
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0002
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0002 128.3
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0002 128.3
VLAN4
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0003
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0003
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0003 128.3
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0003 128.3
目标4:
在VTP CLIENT上将接口配置进正确的VLAN
1. sw3#conf t （划接口进不同的VALN）
Enter configuration commands, one per line. End with CNTL/Z.
sw3(config)#interface f0/14
sw3(config-if)#switchport access vlan 2
sw3(config-if)#switchport mode access
sw3(config-if)#no sh
sw3(config-if)#exit
sw3(config)#interface f0/15
sw3(config-if)#switchport access vlan 3
sw3(config-if)#switchport mode access
sw3(config-if)#no sh
sw3(config-if)#exit
sw3(config)#exit
sw3#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
2 v2 active Fa0/14
3 v3 active Fa0/15
4 v4 active
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
sw3#show spanning-tree br
VLAN1
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0000
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.0f1c.0000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0000 128.2
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0000 128.2
VLAN2
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0001
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.0f1c.0001
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0001 128.2
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0001 128.2
FastEthernet0/14 128.15 128 19 FWD 19 32768 cc00.0f1c.0001 128.15
VLAN3
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0002
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.0f1c.0002
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0002 128.2
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0002 128.2
FastEthernet0/15 128.16 128 19 FWD 19 32768 cc00.0f1c.0002 128.16
VLAN4
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0003
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.0f1c.0003
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0003 128.2
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0003 128.2
2． sw4#conf t
Enter configuration commands, one per line. End with CNTL/Z.
sw4(config)#interface f0/14
sw4(config-if)#switchport access vlan 3
sw4(config-if)#switchport mode access
sw4(config-if)#no sh
sw4(config-if)#exit
sw4(config)#interface f0/15
sw4(config-if)#switchport access vlan 4
sw4(config-if)#switchport mode access
sw4(config-if)#no sh
sw4(config-if)#exit
sw4(config)#exit
sw4#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
2 v2 active
3 v3 active Fa0/14
4 v4 active Fa0/15
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
sw4#show spanning-tree br
VLAN1
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0000
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0000 128.3
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0000 128.3
VLAN2
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0001
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0001
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0001 128.3
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0001 128.3
VLAN3
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0002
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0002
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0002 128.3
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0002 128.3
FastEthernet0/14 128.15 128 19 FWD 19 32768 cc00.058c.0002 128.15
VLAN4
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0003
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0003
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0003 128.3
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0003 128.3
FastEthernet0/15 128.16 128 19 FWD 19 32768 cc00.058c.0003 128.16
3．sw5#conf t
Enter configuration commands, one per line. End with CNTL/Z.
sw5(config)#interface f0/14c
sw5(config-if)#switchport access vlan 4
sw5(config-if)#switchport mode access
sw5(config-if)#no sh
sw5(config-if)#exit
sw5(config)#interface f0/15
sw5(config-if)#switchport access vlan 2
sw5(config-if)#switchport mode access
sw5(config-if)#no sh
sw5(config-if)#exit
sw5(config)#exit
sw5#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
2 v2 active Fa0/15
3 v3 active
4 v4 active Fa0/14
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
sw5#show spanning-tree br
VLAN1
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0000
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.07dc.0000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0000 128.4
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0000 128.4
VLAN2
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0001
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.07dc.0001
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0001 128.4
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0001 128.4
FastEthernet0/15 128.16 128 19 FWD 19 32768 cc00.07dc.0001 128.16
VLAN3
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0002
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.07dc.0002
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0002 128.4
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0002 128.4
VLAN4
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0003
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.07dc.0003
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0003 128.4
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0003 128.4
FastEthernet0/14 128.15 128 19 FWD 19 32768 cc00.07dc.0003 128.15
分析：很明显，VLAN 这次的显示和第一次的有些不同，接口划分到VLAN 中后，它们的端口所属也在发生变化，但是，不变的是，它们一直都是处于转发状态。
4.测试相同VLAN中的主机是否能够通信.
分析：
由此可见，相同VLAN 不同交换机的VALN是可以PING 通的了。不 同VALN 之间目前还是不能PING 通。
实验目标:
目标1. 按照实验要求连接拓扑
目标2. 配置VTP域：SWITCH1、SWITCH2为VTP SERVER并开启VLTP修剪；SWITCH3、SWITCH4为VTP CLIENT；并在SERVER上创建VLAN2、3、4
目标3. 将SWITCH1配置为VLAN1、VLAN3的根桥，VLAN2、VLAN4的次根桥
将SWITCH2配置为VLAN2、VLAN4的根桥，VLAN1、VLAN3的次根桥
目标4. 在VTP CLIENT上将接口配置进正确的VLAN
目标5. 配置SWITCH1和SWITCH2之间的以太网通道
目标6. 在SWITCH1、SWITCH2、ROUTER1上配置RIP路由协议
目标7. 测试网络联通性：VLAN内PC连通性；VLAN间PC连通性；VLAN内PC与INTERNET连通性
实验步骤:
目标1:
1.搭环境.
Router1 E0/0 <----> Switch1 F0/0
Router1 E0/1 <----> Switch2 F0/0
Switch1 F0/14 <----> Switch2 F0/14
Switch1 F0/15 <----> Switch2 F0/15
Switch1 F0/1 <----> Switch3 F0/1
Switch1 F0/2 <----> Switch4 F0/1
Switch1 F0/3 <----> Switch5 F0/1
Switch2 F0/1 <----> Switch3 F0/2
Switch2 F0/2 <----> Switch4 F0/2
Switch2 F0/3 <----> Switch5 F0/2
Switch3 F0/14 <----> VPCS V0/1
Switch3 F0/15 <----> VPCS V0/2
Switch4 F0/14 <----> VPCS V0/3
Switch4 F0/15 <----> VPCS V0/4
Switch5 F0/14 <----> VPCS V0/5
Switch5 F0/15 <----> VPCS V0/6
2.R1相关配置:
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#interface e0/0
R1(config-if)#ip add 10.1.1.1 255.255.255.0
R1(config-if)#no sh
R1(config)#interface e0/1
R1(config-if)#ip add 10.1.2.1 255.255.255.0
R1(config-if)#no sh
R1(config-if)#exit
R1(config)#
R1#show ip in br
Interface IP-Address OK? Method Status Protocol
Ethernet0/0 10.1.1.1 YES manual up up
Ethernet0/1 10.1.2.1 YES manual up up
Ethernet0/2 unassigned YES unset administratively down down
Ethernet0/3 unassigned YES unset administratively down down
Loopback0 202.16.2.1 YES manual up up
R1#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
C 202.16.2.0/24 is directly connected, Loopback0
10.0.0.0/24 is subnetted, 2 subnets
C 10.1.2.0 is directly connected, Ethernet0/1
C 10.1.1.0 is directly connected, Ethernet0/0
目标2:
配置VTP域：SWITCH1、SWITCH2为VTP SERVER并开启VLTP修 剪；SWITCH3、SWITCH4，5为VTP CLIENT；并在SERVER上创建VLAN2、 3、4
1．sw1-3(config)#interface ra （trunk）
sw1-3(config)#interface range f0/0 - 3
sw1-3(config-if-range)#switchport mode trunk
sw1-3(config-if-range)#no sh
sw1-3(config-if-range)#exit
sw1-3(config)#interface range f0/14 - 15
sw1-3(config-if-range)#switchport mode trunk
sw1-3(config-if-range)#no sh
2．sw1-3#show interfaces switchp (test trunk)
Name: Fa0/0
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/2
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/3
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/14
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/15
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
3. SW2-3上面配置TRUNK 和SW1-3 同样的过程。（详细过程略）
4．sw3(config)#interface ra f0/1 -2 （TRUNK）
sw3(config-if-range)#switchport mode trunk
sw3(config-if-range)#no sh
sw3#show interfaces switchport
Name: Fa0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Appliance trust: none
Name: Fa0/2
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Disabled
Access Mode VLAN: 0 ((Inactive))
Trunking Native Mode VLAN: 1 (default)
Trunking VLANs Enabled: ALL
Trunking VLANs Active: 1
Priority for untagged frames: 0
Override vlan tag priority: FALSE
Voice VLAN: none
Applianc
5. sw4(config)#interface range f0/1 -2
sw4(config-if-range)#switchport mode trunk
sw4(config-if-range)#no sh
sw4(config-if-range)#exit
sw4(config)#exit
sw5(config)#interface range f0/1 -2
sw5(config-if-range)#switchport mode trunk
sw5(config-if-range)#no sh
6. sw1-3# vl da (start vtp)
sw1-3(vlan)#vtp domain test
Changing VTP domain name from NULL to test
sw1-3(vlan)#vtp server
Device mode already VTP SERVER.
sw1-3(vlan)#vtp password 111111
Setting device VLAN database password to 111111.
sw1-3(vlan)#vtp v2-mode
V2 mode enabled.
sw1-3(vlan)#vtp pruning
Pruning switched ON
sw1-3(vlan)#exit
APPLY completed.
Exiting....
sw1-3#show vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Server
VTP Domain Name : test
VTP Pruning Mode : Enabled
VTP V2 Mode : Enabled
VTP Traps Generation : Disabled
MD5 digest : 0xEE 0x18 0x41 0xD1 0x2B 0xFB 0x4F 0x52
Configuration last modified by 0.0.0.0 at 3-1-02 00:49:43
Local updater ID is 0.0.0.0 (no valid interface found)
sw1-3#
7. sw2-3#vl da (start vtp)
sw2-3(vlan)#vtp domain test
Changing VTP domain name from test\ to test
sw2-3(vlan)#vtp server
Device mode already VTP SERVER.
sw2-3(vlan)#vtp password 111111
Setting device VLAN database password to 111111.
sw2-3(vlan)#vtp v2-mode
V2 mode enabled.
sw2-3(vlan)#vtp pruning
Pruning switched ON
sw2-3(vlan)#exit
APPLY completed.
Exiting....
sw2-3#show vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Server
VTP Domain Name : test
VTP Pruning Mode : Enabled
VTP V2 Mode : Enabled
VTP Traps Generation : Disabled
MD5 digest : 0x7A 0x2A 0x67 0xAE 0x1E 0xBE 0x30 0x0E
Configuration last modified by 0.0.0.0 at 3-1-02 00:52:44
Local updater ID is 0.0.0.0 (no valid interface found)
sw2-3#
8. sw3#vl da (start vtp client)
sw3(vlan)#vtp domain test
Domain name already set to test .
sw3(vlan)#vtp client
Setting device to VTP CLIENT mode.
sw3(vlan)#vtp password 111111
Setting device VLAN database password to 111111.
sw3(vlan)#exit
In CLIENT state, no apply attempted.
Exiting....
sw3#show vtp st
sw3#show vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Client
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x05 0xFC 0x00 0x59 0x49 0xAF 0x1D 0xE2
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
sw4#vl da (start vtp client)
sw4(vlan)#vtp domain test
Domain name already set to test .
sw4(vlan)#vtp client
Setting device to VTP CLIENT mode.
sw4(vlan)#vtp password 111111
Setting device VLAN database password to 111111.
sw4(vlan)#exit
In CLIENT state, no apply attempted.
Exiting....
sw4#show vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Client
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x05 0xFC 0x00 0x59 0x49 0xAF 0x1D 0xE2
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
sw4#
sw5#vl da (start vtp client)
sw5(vlan)#vtp domain test
Domain name already set to test .
sw5(vlan)#vtp client
Setting device to VTP CLIENT mode.
sw5(vlan)#vtp password 111111
Setting device VLAN database password to 111111.
sw5(vlan)#exit
In CLIENT state, no apply attempted.
Exiting....
sw5#show vtp status
VTP Version : 2
Configuration Revision : 0
Maximum VLANs supported locally : 256
Number of existing VLANs : 5
VTP Operating Mode : Client
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x05 0xFC 0x00 0x59 0x49 0xAF 0x1D 0xE2
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
sw5#
9. sw1-3#vl da (create vlan 2,3,4.)
sw1-3(vlan)#vlan 2 name v2
VLAN 2 added:
Name: v2
sw1-3(vlan)#apply
APPLY completed.
sw1-3(vlan)#vlan 3 name v3
VLAN 3 added:
Name: v3
sw1-3(vlan)#apply
APPLY completed.
sw1-3(vlan)#vlan 4 name v4
VLAN 4 added:
Name: v4
sw1-3(vlan)#apply
APPLY completed.
sw1-3(vlan)#exit
APPLY completed.
Exiting....
sw1-3#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/4, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13
2 v2 active
3 v3 active
4 v4 active
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
10.client test
sw2-3#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/4, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13
2 v2 active
3 v3 active
4 v4 active
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
sw3#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15
2 v2 active
3 v3 active
4 v4 active
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
sw4#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15
2 v2 active
3 v3 active
4 v4 active
sw5#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15
2 v2 active
3 v3 active
4 v4 active
目标3:
将SWITCH1配置为VLAN1、VLAN3的根桥，VLAN2、VLAN4的次根桥
将SWITCH2配置为VLAN2、VLAN4的根桥，VLAN1、VLAN3的次根桥
1. sw1-3#conf t (config stp)
sw1-3(config)#spanning-tree vlan 1 root primary
% This switch is already the root of VLAN1 spanning tree
VLAN 1 bridge priority set to 8192
VLAN 1 bridge max aging time unchanged at 20
VLAN 1 bridge hello time unchanged at 2
VLAN 1 bridge forward delay unchanged at 15
sw1-3(config)#spanning-tree vlan 3 root primary
% This switch is already the root of VLAN3 spanning tree
VLAN 3 bridge priority set to 8192
VLAN 3 bridge max aging time unchanged at 20
VLAN 3 bridge hello time unchanged at 2
VLAN 3 bridge forward delay unchanged at 15
sw1-3(config)#spanning-tree vlan 2 root secondary
VLAN 2 bridge priority set to 16384
VLAN 2 bridge max aging time unchanged at 20
VLAN 2 bridge hello time unchanged at 2
VLAN 2 bridge forward delay unchanged at 15
sw1-3(config)#spanning-tree vlan 4 root secondary
VLAN 4 bridge priority set to 16384
VLAN 4 bridge max aging time unchanged at 20
VLAN 4 bridge hello time unchanged at 2
VLAN 4 bridge forward delay unchanged at 15
.
sw1-3#show spanning-tree br
VLAN1
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0000
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 8192
Address cc00.00f8.0000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/0 128.1 128 19 FWD 0 8192 cc00.00f8.0000 128.1
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0000 128.2
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.00f8.0000 128.3
FastEthernet0/3 128.4 128 19 FWD 0 8192 cc00.00f8.0000 128.4
FastEthernet0/14 128.15 128 19 FWD 0 8192 cc00.00f8.0000 128.15
FastEthernet0/15 128.16 128 19 FWD 0 8192 cc00.00f8.0000 128.16
--More―
2. sw2-3#conf t
Enter configuration commands, one per line. End with CNTL/Z.
sw2-3(config)#spanning-tree vlan 2 root primary
VLAN 2 bridge priority set to 8192
VLAN 2 bridge max aging time unchanged at 20
VLAN 2 bridge hello time unchanged at 2
VLAN 2 bridge forward delay unchanged at 15
sw2-3(config)#spanning-tree vlan 4 root primary
VLAN 4 bridge priority set to 8192
VLAN 4 bridge max aging time unchanged at 20
VLAN 4 bridge hello time unchanged at 2
VLAN 4 bridge forward delay unchanged at 15
sw2-3(config)#spanning-tree vlan 1 root secondary
VLAN 1 bridge priority set to 16384
VLAN 1 bridge max aging time unchanged at 20
VLAN 1 bridge hello time unchanged at 2
VLAN 1 bridge forward delay unchanged at 15
sw2-3(config)#spanning-tree vlan 3 root secondary
VLAN 3 bridge priority set to 16384
VLAN 3 bridge max aging time unchanged at 20
VLAN 3 bridge hello time unchanged at 2
VLAN 3 bridge forward delay unchanged at 15
3. w4#show spanning-tree br (test stp )
VLAN1
Spanning enabled protocol ieee
Root ID Priority 81 92
Address cc00.00f8.0000
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0000 128.3
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0000 128.3
FastEthernet0/14 128.15 128 19 FWD 19 32768 cc00.058c.0000 128.15
FastEthernet0/15 128.16 128 19 FWD 19 32768 cc00.058c.0000 128.16
VLAN2
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0001
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0001
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0001 128.3
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0001 128.3
VLAN3
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0002
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0002
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0002 128.3
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0002 128.3
VLAN4
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0003
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0003
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0003 128.3
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0003 128.3
目标4:
在VTP CLIENT上将接口配置进正确的VLAN
1. sw3#conf t （划接口进不同的VALN）
Enter configuration commands, one per line. End with CNTL/Z.
sw3(config)#interface f0/14
sw3(config-if)#switchport access vlan 2
sw3(config-if)#switchport mode access
sw3(config-if)#no sh
sw3(config-if)#exit
sw3(config)#interface f0/15
sw3(config-if)#switchport access vlan 3
sw3(config-if)#switchport mode access
sw3(config-if)#no sh
sw3(config-if)#exit
sw3(config)#exit
sw3#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
2 v2 active Fa0/14
3 v3 active Fa0/15
4 v4 active
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
sw3#show spanning-tree br
VLAN1
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0000
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.0f1c.0000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0000 128.2
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0000 128.2
VLAN2
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0001
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.0f1c.0001
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0001 128.2
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0001 128.2
FastEthernet0/14 128.15 128 19 FWD 19 32768 cc00.0f1c.0001 128.15
VLAN3
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0002
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.0f1c.0002
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0002 128.2
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0002 128.2
FastEthernet0/15 128.16 128 19 FWD 19 32768 cc00.0f1c.0002 128.16
VLAN4
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0003
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.0f1c.0003
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0003 128.2
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0003 128.2
2． sw4#conf t
Enter configuration commands, one per line. End with CNTL/Z.
sw4(config)#interface f0/14
sw4(config-if)#switchport access vlan 3
sw4(config-if)#switchport mode access
sw4(config-if)#no sh
sw4(config-if)#exit
sw4(config)#interface f0/15
sw4(config-if)#switchport access vlan 4
sw4(config-if)#switchport mode access
sw4(config-if)#no sh
sw4(config-if)#exit
sw4(config)#exit
sw4#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
2 v2 active
3 v3 active Fa0/14
4 v4 active Fa0/15
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
sw4#show spanning-tree br
VLAN1
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0000
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0000 128.3
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0000 128.3
VLAN2
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0001
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0001
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0001 128.3
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0001 128.3
VLAN3
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0002
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0002
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0002 128.3
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0002 128.3
FastEthernet0/14 128.15 128 19 FWD 19 32768 cc00.058c.0002 128.15
VLAN4
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0003
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.058c.0003
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0003 128.3
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0003 128.3
FastEthernet0/15 128.16 128 19 FWD 19 32768 cc00.058c.0003 128.16
3．sw5#conf t
Enter configuration commands, one per line. End with CNTL/Z.
sw5(config)#interface f0/14c
sw5(config-if)#switchport access vlan 4
sw5(config-if)#switchport mode access
sw5(config-if)#no sh
sw5(config-if)#exit
sw5(config)#interface f0/15
sw5(config-if)#switchport access vlan 2
sw5(config-if)#switchport mode access
sw5(config-if)#no sh
sw5(config-if)#exit
sw5(config)#exit
sw5#show vlan-switch
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/0, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
2 v2 active Fa0/15
3 v3 active
4 v4 active Fa0/14
1002 fddi-default active
1003 trcrf-default active
1004 fddinet-default active
1005 trbrf-default active
sw5#show spanning-tree br
VLAN1
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0000
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.07dc.0000
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0000 128.4
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0000 128.4
VLAN2
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0001
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.07dc.0001
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0001 128.4
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0001 128.4
FastEthernet0/15 128.16 128 19 FWD 19 32768 cc00.07dc.0001 128.16
VLAN3
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.00f8.0002
Cost 19
Port 2 (FastEthernet0/1)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.07dc.0002
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 FWD 0 8192 cc00.00f8.0002 128.4
FastEthernet0/2 128.3 128 19 BLK 19 16384 cc00.088c.0002 128.4
VLAN4
Spanning tree enabled protocol ieee
Root ID Priority 8192
Address cc00.088c.0003
Cost 19
Port 3 (FastEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32768
Address cc00.07dc.0003
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Interface Designated
Name Port ID Prio Cost Sts Cost Bridge ID Port ID
-------------------- ------- ---- ----- --- ----- -------------------- -------
FastEthernet0/1 128.2 128 19 BLK 19 16384 cc00.00f8.0003 128.4
FastEthernet0/2 128.3 128 19 FWD 0 8192 cc00.088c.0003 128.4
FastEthernet0/14 128.15 128 19 FWD 19 32768 cc00.07dc.0003 128.15
分析：很明显，VLAN 这次的显示和第一次的有些不同，接口划分到VLAN 中后，它们的端口所属也在发生变化，但是，不变的是，它们一直都是处于转发状态。
4.测试相同VLAN中的主机是否能够通信.
分析：
由此可见，相同VLAN 不同交换机的VALN是可以PING 通的了。不 同VALN 之间目前还是不能PING 通。
内容来自用户分享和网络整理，不保证内容的准确性，如有侵权内容，可联系管理员处理 
相关文章推荐
- [Visual Studio 2010] 开发与测试敏捷特性
- Visual Studio 2010 Ultimate开发与测试敏捷特性
- 关于在Office 2010,Visual Studio 2010环境下开发Office 2007解决方案的问题
- Visual Studio 2010新特性:更适合Web开发
- 关于在Office 2010,Visual Studio 2010环境下开发Office 2007解决方案的问题
- 基于Visual Studio 2010与Office 2010开发办公自动化应用(VSTO)
- ASP.NET 4 风云之旅系列之Visual Studio 2010在Web开发方面的新特性
- Visual Studio 2010开发与测试敏捷特性
- Visual Studio 2010 和 Boost库编译、开发
- Visual Studio 2013 Web开发新特性
- MOSS 2010：Visual Studio 2010开发体验（2）——项目模板和结构
- 提高你开发效率的十五个Visual Studio 2010使用技巧
- 基于Visual Studio 2010 进行敏捷/Scrum模式开发
- WIN7 32位+Visual Studio 2010 安装OPENSSL开发包
- 基于Visual Studio 2010 进行敏捷/Scrum模式开发
- 基于Visual Studio 2003/2005的Office插件开发FAQ
- Visual Studio 2008开发新特性系列课程(1)：Visual Studio 2008 面面观
- Visual Studio 2008开发新特性系列课程(9)：开发 SharePoint工作流
- 基于Visual Studio 2010 阐述C#4个特性
- (转)微软今天公布了下一代Visual Studio和.NET Framework开发工具和平台,该平台将被命名的Visual Studio 2010和.Net Framework 4.0.