Cisco Router and switch 配置命令(十)
2009-08-06 10:05
381 查看
1、 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令:
router(config-if)#mls rp management-interface
2、 要检验MLS-RP的配置情况:
router# show mls rp
3、 检验特定接口上的MLS配置:
router# show mls rp interface interface number
4、为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表:
set mls flow [destination|destination-source|full]
5、为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令:
router(config)# mls rp ip input-acl
6、当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令:
switch(enable) set mls enable
7、 若想改变老化时间的值,可在特权模式下输入以下命令:
switch(enable) set mls agingtime agingtime
8、设置快速老化:
switch(enable) set mls agingtime fast fastagingtime pkt_threshold
9、确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定:
switch(enable) show mls include
10、显示MLS高速缓存记录:
switch(enable) show mls entry
11、用命令show in arp显示ARP高速缓存区的内容。
12、要把路由器配置为HSRP备份组的成员,可以在接口配置模式下使用下面的命令:
router(config-if)# standby group-number ip ip-address
13、为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下:
router(config-if)# standy group-number preempt
14、访问时间和保持时间参数是可配置的:
router(config-if)# standy group-number timers hellotime holdtime
60. 配置HSRP跟踪:
router(config-if)# standy group-number track type-number interface-priority
15、要显示HSRP路由器的状态:
router# show standby type-number group brief
16、 用命令show ip igmp确定当选的查询器。
17、启动IP组播路由选择:
router(config)# ip muticast-routing
18、启动接口上的PIM:
dalllasr1>(config-if)# ip pim {dense-mode|sparse-mode|sparse-dense-mode}
19、启动稀疏-稠密模式下的PIM:
router# ip multicast-routing
router# interface type number
router# ip pim sparse-dense-mode
20、 核实PIM的配置:
dallasr1># show ip pim interface[type number] [count]
21、显示PIM邻居:
dallasr1># show ip neighbor type number
22、为了配置RP的地址,命令如下:
dallasr1># ip pim rp-address ip-address [group-access-list-number][override]
23、选择一个默认的RP:
dallasr1># ip pim rp-address
通告RP和它所服务的组范围:
dallasr1># ip pim send-rp-announce type number scope ttl group-list access-list-number
为管理范围组通告RP的地址:
dallasr1># ip pim send-rp-announce ethernet0 scope 16 group-list1
dallasr1># access-list 1 permit 266.0.0.0 0.255.255.255
设定一个RP映像代理:
dallasr1># ip pim send-rp-discovery scope ttl
核实组到RP的映像:
dallasr1># show ip pim rp mapping
dallasr1># show ip pim rp [group-name|group-address] [mapping]
router(config-if)#mls rp management-interface
2、 要检验MLS-RP的配置情况:
router# show mls rp
3、 检验特定接口上的MLS配置:
router# show mls rp interface interface number
4、为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表:
set mls flow [destination|destination-source|full]
5、为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令:
router(config)# mls rp ip input-acl
6、当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令:
switch(enable) set mls enable
7、 若想改变老化时间的值,可在特权模式下输入以下命令:
switch(enable) set mls agingtime agingtime
8、设置快速老化:
switch(enable) set mls agingtime fast fastagingtime pkt_threshold
9、确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定:
switch(enable) show mls include
10、显示MLS高速缓存记录:
switch(enable) show mls entry
11、用命令show in arp显示ARP高速缓存区的内容。
12、要把路由器配置为HSRP备份组的成员,可以在接口配置模式下使用下面的命令:
router(config-if)# standby group-number ip ip-address
13、为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下:
router(config-if)# standy group-number preempt
14、访问时间和保持时间参数是可配置的:
router(config-if)# standy group-number timers hellotime holdtime
60. 配置HSRP跟踪:
router(config-if)# standy group-number track type-number interface-priority
15、要显示HSRP路由器的状态:
router# show standby type-number group brief
16、 用命令show ip igmp确定当选的查询器。
17、启动IP组播路由选择:
router(config)# ip muticast-routing
18、启动接口上的PIM:
dalllasr1>(config-if)# ip pim {dense-mode|sparse-mode|sparse-dense-mode}
19、启动稀疏-稠密模式下的PIM:
router# ip multicast-routing
router# interface type number
router# ip pim sparse-dense-mode
20、 核实PIM的配置:
dallasr1># show ip pim interface[type number] [count]
21、显示PIM邻居:
dallasr1># show ip neighbor type number
22、为了配置RP的地址,命令如下:
dallasr1># ip pim rp-address ip-address [group-access-list-number][override]
23、选择一个默认的RP:
dallasr1># ip pim rp-address
通告RP和它所服务的组范围:
dallasr1># ip pim send-rp-announce type number scope ttl group-list access-list-number
为管理范围组通告RP的地址:
dallasr1># ip pim send-rp-announce ethernet0 scope 16 group-list1
dallasr1># access-list 1 permit 266.0.0.0 0.255.255.255
设定一个RP映像代理:
dallasr1># ip pim send-rp-discovery scope ttl
核实组到RP的映像:
dallasr1># show ip pim rp mapping
dallasr1># show ip pim rp [group-name|group-address] [mapping]
相关文章推荐
- Cisco Router and switch 配置命令(五)
- Cisco Router and switch 配置命令(十一)
- Cisco Router and switch 配置命令(六)
- Cisco Router and switch 配置命令(一)
- Cisco Router and switch 配置命令(七)
- Cisco Router and switch 配置命令(二)
- Cisco Router and switch 配置命令(八)
- Cisco Router and switch 配置命令(三)
- Cisco Router and switch 配置命令(四)
- Cisco Router and switch 配置命令(九)
- Router and switch 配置命令精华压缩版
- Router and switch 配置命令精华压缩版
- Router and switch 配置命令精华压缩版
- CISCO SWITCH &ROUTER基本配置命令
- Router and switch 配置命令精华
- Router and switch 配置命令精华压缩版
- How to reset password for cisco router and switch
- cisco switch router 交换机,路由器常用配置和实例
- CISCO-Router常用配置命令大全(A-X)