about ubuntu hard disk
2008-01-26 17:29
225 查看
DanielHahler/Bug59695
Bug 59695 ("default value in power.sh potentially kills laptop disks") is about not preventing bad behaviour of drives (high Load_Cycle_Count numbers) on (laptop) harddrives.
Because the bug report has 150 comments already, I've tried to summarize it here.
There appear to be two issues here: HDD spin down and "Power cycling", whereas the first one has a
relative short default (60 seconds), but the latter one gets the most complains (it's about Load_Cycle_Count).
The disk Load_Cycle_Count issue appears to be caused by a combination of two problems -- The first is overly-aggressive power management from what might be considered buggy hardware. The second is that Ubuntu appears to be touching the hard drive on a regular basis for one reason or another.
Note: In sections below relating to how to prevent damage to your hard disk, you should replace $HDD everywhere with your device, e.g. "/dev/sda" or "/dev/hda". If you have several harddrives, you need to change it accordingly and duplicate lines in workarounds.
Check
You can check the current value of Load_Cycle_Count of your harddrive(s) using:sudo smartctl -a $HDD | grep Load_Cycle_Count
(You need the smartmontools package for this. I also had to enable SMART monitoring for my drives using sudo smartctl -s on $HDD)
The values for this differ a lot (e.g. it's 0 on my desktop), but it goes up to > 600.000 for others, depending on the lifetime. TODO: add a section with sample values (including the value of Power_On_Hours).
What Ubuntu does
Itappears to be the official policy of Ubuntu that by default, Ubuntu should not adjust any power management settings of the harddisk. Unfortunately, this policy has two negative effects: It leaves quite a few people with broken hard drives that would otherwise not be broken, and it quite simply makes people who love Ubuntu feel neglected. This issue has been going on a long time.
The problem appears to be that some manufacturers' defaults are too aggressive and that Ubuntu might cause too many unbuffered disk accesses -- the combination of which can cause over a thousand parks a day on some systems.
In /etc/acpi/power.sh, laptop mode gets handled. If it gets enabled, hdparm is called with "-B 1", if it gets disabled with "-B 254". 254 is the least aggressive setting. 255 is off, but does not work for all disks.
In power.sh also the spindown timeout gets set, according to SPINDOWN_TIME from /etc/default/acpi-support (default: 12). This results in spinning down the harddrive after 12*5=60 seconds of inactivitiy. This does not influence Load_Cycle_Count however.
apm
"/etc/apm" is not supposed to be used, but if it would get, it sets spindown to 60 seconds - but does not affect the general APM setting (hdparm -B). (there's a bug, which also used "power_conserve" here, if on_ac_power return "don't know" -
bug 156893)
Debug
Blue has created a script, which acts as a wrapper around hdparm and logs, where it's called (including its arguments) From his report, it appears that hdparm always gets called through apm or the init script (the logfile excerpt appears to be from booting).
TODO: provide said helper script, allowing others to help to debug this.
Workaround
Various workarounds have been provided.Try hdparm -B 255 $HDD or hdparm -B 254 $HDD. (255 is supposed to disable APM, but it does not work for some; so 254 sets it to the less aggressive setting)
There are different methods to keep this setting after reboot/resume. Your mileage may vary. There may be more workarounds in the bug report, but essentially, all are using "hdparm -B" to change the apm handling of the harddrive.
http://ubuntuforums.org/showpost.php?p=3675960&postcount=26
UbuntuDemon I brought some of these proposed fixes together in the hope that is easier to apply for users who are suffering from this problem
Force hdparm values in acpi hooks
Gilles posted the following workaround: Create a file called 99-fix-park.sh (keep the '99-' and the '.sh', but you can name the file as you like otherwise) with the following two lines:#!/bin/sh hdparm -B 254 $HDD
and copy it to the following directories: /etc/acpi/resume.d/ and /etc/acpi/start.d/ (
https://launchpad.net/ubuntu/+source/acpi-support/+bug/59695/comments/10)
laptop-mode-tools
Don posted another workaround: Install laptop-mode-tools and set CONTROL_HD_POWERMGMT=1 in /etc/laptop-mode/laptop-mode.conf (https://launchpad.net/ubuntu/+source/acpi-support/+bug/59695/comments/19) Here's another more verbose setup of laptop-mode-tools from Michael:
https://launchpad.net/ubuntu/+source/acpi-support/+bug/59695/comments/63
Proposed fixes
FIXED: Converted most remaining 255's to 254s, and added an explanation.Conclusion
This bug report has attracted a lot of concerned Ubuntu users and it seems quite clear from the user feedback, that other operating systems/distributions handle this better. However, the workaround should be quite simple and this wiki page is a first attempt, to fix this for the better.Misc
ubuntu_demon has put together a list of TODOs:https://launchpad.net/ubuntu/+source/acpi-support/+bug/59695/comments/81
Comments
Please leave any comments/additions here. You may also edit the page directly, but please try to be clear and helpful. The problem has been confirmed and we know that it's a critical thing - please do not repeat that the bug status should be critical.Could you kindly explain how to diagnose whether the settings on a system, at a point of time, are correct. I have followed the instructions but still find the load cycle count increasing. How do I diagnose the problem?
last edited 2007-11-12 23:26:01 by VikasRawal
相关文章推荐
- Ubuntu 10 install problem maybe the hard disk has installed windows 7
- install ubuntu on windows 7 from hard disk
- Ubuntu - 硬盘分区、格式化、自动挂载配置 | Hard disk add new partition, format, auto mount in ubuntu
- Ubuntu - 硬盘分区、格式化、自动挂载配置 | Hard disk add new partition, format, auto mount in ubuntu
- ubuntu harddisk uuid already exists
- Ubuntu - 硬盘分区、格式化、自动挂载配置 | Hard disk add new partition, format, auto mount in ubuntu
- Resizing the disk space on Ubuntu Server VMs running on VMware ESXi 5
- VirtualBox 启动报错 could not find an open hard disk with uuid 解决方法
- Solve Linux & Unix Systems Hard Disk Problems
- about ubuntu apt keyring
- VMware启动Ubuntu时出现错误Cannot open the disk 'xxxxxxx.vmdk' or one of the snapshot disks it depends on. .
- 装完UBUNTU后无法启动win7,选择win7 loader出现A read disk error occurred
- Ubuntu --- not enough free disk space
- lvm add new hard disk for oracle linux 5.8
- Installing GRUB on a Hard Disk Image File
- mount NTFS harddisk on slackware ver13.37
- Hard disk Partition/format
- MISCONF Redis is configured to save RDB snapshots, but is currently not able to persist on disk. Commands that may modify the data set are disabled. Please check Redis logs for details about the error
- VC++获取计算机Hardware Information (CPU ID, MainBoard Info, Hard Disk Serial, System Information)
- P2V Ubuntu 10.10 to VirtualBox Disk