您的位置:首页 > 运维架构 > Linux

Linux 添加开机启动方法(服务/脚本)

2020-03-12 07:10 495 查看

系统启动时需要加载的配置文件

/etc/profile、/root/.bash_profile
/etc/bashrc、/root/.bashrc
/etc/profile.d/*.sh、/etc/profile.d/lang.sh
/etc/sysconfig/i18n、/etc/rc.local(/etc/rc.d/rc.local)

一、修改开机启动文件:/etc/rc.local(或者/etc/rc.d/rc.local)

# 1.编辑rc.local文件
[root@localhost ~]# vi /etc/rc.local

# 2.修改rc.local文件,在 exit 0 前面加入以下命令。保存并退出。
/etc/init.d/mysqld start                     # mysql开机启动
/etc/init.d/nginx start                     # nginx开机启动
supervisord -c /etc/supervisor/supervisord.conf         # supervisord开机启动
/bin/bash /server/scripts/test.sh >/dev/null 2>/dev/null

# 3.最后修改rc.local文件的执行权限
[root@localhost ~]# chmod +x /etc/rc.local
[root@localhost ~]# chmod 755 /etc/rc.local

二、自己写一个shell脚本

将写好的脚本(.sh文件)放到目录 /etc/profile.d/ 下,系统启动后就会自动执行该目录下的所有shell脚本。

三、通过chkconfig命令设置

# 1.将(脚本)启动文件移动到 /etc/init.d/或者/etc/rc.d/init.d/目录下。(前者是后者的软连接)
mv /www/wwwroot/test.sh /etc/rc.d/init.d

# 2.启动文件前面务必添加如下三行代码,否侧会提示chkconfig不支持。
#!/bin/sh             告诉系统使用的shell,所以的shell脚本都是这样
#chkconfig: 35 20 80        分别代表运行级别,启动优先权,关闭优先权,此行代码必须
#description: http server     自己随便发挥!!!,此行代码必须
/bin/echo $(/bin/date +%F_%T) >> /tmp/test.log

# 3.增加脚本的可执行权限
chmod +x /etc/rc.d/init.d/test.sh

# 4.添加脚本到开机自动启动项目中。添加到chkconfig,开机自启动。
[root@localhost ~]# cd /etc/rc.d/init.d
[root@localhost ~]# chkconfig --add test.sh
[root@localhost ~]# chkconfig test.sh on

# 5.关闭开机启动
[root@localhost ~]# chkconfig test.sh off

# 6.从chkconfig管理中删除test.sh
[root@localhost ~]# chkconfig --del test.sh

# 7.查看chkconfig管理
[root@localhost ~]# chkconfig --list test.sh

四、自定义服务文件,添加到系统服务,通过Systemctl管理

1.写服务文件:如nginx.service、redis.service、supervisord.service

[Unit]:服务的说明
Description:描述服务
After:描述服务类别

[Service]服务运行参数的设置
Type=forking      是后台运行的形式
ExecStart        为服务的具体运行命令
ExecReload       为服务的重启命令
ExecStop        为服务的停止命令
PrivateTmp=True     表示给服务分配独立的临时空间
注意:启动、重启、停止命令全部要求使用绝对路径

[Install]        服务安装的相关设置,可设置为多用户
WantedBy=multi-user.target

2.文件保存在目录下:以754的权限。目录路径:/usr/lib/systemd/system。如上面的supervisord.service文件放在这个目录下面。

[root@localhost ~]# cat /usr/lib/systemd/system/nginx.service
[root@localhost ~]# cat /usr/lib/systemd/system/supervisord.service

3.设置开机自启动(任意目录下执行)。如果执行启动命令报错,则执行:systemctl daemon-reload

设置开机自启动
[root@localhost ~]# systemctl enable nginx.service
[root@localhost ~]# systemctl enable supervisord

停止开机自启动
[root@localhost ~]# systemctl disable nginx.service
[root@localhost ~]# systemctl disable supervisord

验证一下是否为开机启动
[root@localhost ~]# systemctl is-enabled nginx
[root@localhost ~]# systemctl is-enabled supervisord

4.其他命令

启动nginx服务
[root@localhost ~]# systemctl start nginx.service

停止nginx服务
[root@localhost ~]# systemctl start nginx.service

重启nginx服务
[root@localhost ~]# systemctl restart nginx.service

查看nginx服务当前状态
[root@localhost ~]# systemctl status nginx.service

查看所有已启动的服务
[root@localhost ~]# systemctl list-units --type=service

5.服务文件示例:

# supervisord.service进程管理服务文件
[Unit]
Description=Process Monitoring and Control Daemon  # 内容自己定义:Description=Supervisor daemon
After=rc-local.service nss-user-lookup.target

[Service]
Type=forking
ExecStart=/usr/bin/supervisord -c /etc/supervisor/supervisord.conf
ExecStop= /usr/bin/supervisorctl shutdown
ExecReload=/usr/bin/supervisorctl reload
Restart=on-failure
RestartSec=42s
KillMode=process

[Install]
WantedBy=multi-user.target
# nginx.service服务文件
[Unit]
Description=nginx - high performance web server
After=network.target remote-fs.target nss-lookup.target

[Service]
Type=forking
ExecStart=/usr/local/nginx/sbin/nginx -c /usr/local/nginx/conf/nginx.conf
ExecReload=/usr/local/nginx/sbin/nginx -s reload
ExecStop=/usr/local/nginx/sbin/nginx -s stop

[Install]
WantedBy=multi-user.target
# redis.service服务文件
[Unit]
Description=Redis
After=network.target remote-fs.target nss-lookup.target

[Service]
Type=forking
ExecStart=/usr/local/bin/redis-server /etc/redis.conf
ExecStop=kill -INT `cat /tmp/redis.pid`
User=www
Group=www

[Install]
WantedBy=multi-user.target

以上就是本文的全部内容,希望对大家的学习有所帮助

您可能感兴趣的文章:

内容来自用户分享和网络整理,不保证内容的准确性,如有侵权内容,可联系管理员处理 点击这里给我发消息
标签:  Linux 开机启动 脚本