20160809下午14:00公司断网处理过程(网络架构VSS模式) 推荐
2016-08-09 09:35
465 查看
收到通知公司断网,公司核心交换机是两台cisco4507做了VSS,但是由于出口线只有一个跟所以没有正常切换,进入机房发现主交换机办卡都是亮红灯,经过重启,恢复正常。
但是楼层网络依然不通,进入弱电间,查看交换机端口不亮。
console进入交换机,发现error-disable
ZPBMC-F16-1#show etherchannel summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use f - failed to allocate aggregator
M - not in use, minimum links not met
u - unsuitable for bundling
w - waiting to be aggregated
d - default port
Number of channel-groups in use: 2
Number of aggregators: 2
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
16 Po16(SU) - Gi1/0/25(P) Gi1/0/26(P) Gi1/0/27(D)
Gi1/0/28(D)
24 Po24(SU) - Gi1/0/23(P) Gi1/0/24(D)
ZPBMC-F16-1#config
ZPBMC-F16-1#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
ZPBMC-F16-1(config)#interface port-channel 16
ZPBMC-F16-1(config-if)#shutdown---等交换机显示关闭状态后再执行下面的命令。
ZPBMC-F16-1(config-if)#no shutdown
先暂时恢复网络,晚上又把主备两台交换机调换位置,有问题的交换机转换为备用
把交换机配置互相配置
发现依然不同,路由走不同
经过检查,需要对交换机引擎做force-switchover
另外出口端口的IP地址需要重新配置成原来主的交换机出口端的地址,并取消原来端口 IP,经过测试恢复正常。
另外附error-disable的处理方式:
http://sfwang.blog.51cto.com/441426/1254137/
但是楼层网络依然不通,进入弱电间,查看交换机端口不亮。
console进入交换机,发现error-disable
ZPBMC-F16-1#show etherchannel summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use f - failed to allocate aggregator
M - not in use, minimum links not met
u - unsuitable for bundling
w - waiting to be aggregated
d - default port
Number of channel-groups in use: 2
Number of aggregators: 2
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
16 Po16(SU) - Gi1/0/25(P) Gi1/0/26(P) Gi1/0/27(D)
Gi1/0/28(D)
24 Po24(SU) - Gi1/0/23(P) Gi1/0/24(D)
ZPBMC-F16-1#config
ZPBMC-F16-1#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
ZPBMC-F16-1(config)#interface port-channel 16
ZPBMC-F16-1(config-if)#shutdown---等交换机显示关闭状态后再执行下面的命令。
ZPBMC-F16-1(config-if)#no shutdown
先暂时恢复网络,晚上又把主备两台交换机调换位置,有问题的交换机转换为备用
把交换机配置互相配置
发现依然不同,路由走不同
经过检查,需要对交换机引擎做force-switchover
另外出口端口的IP地址需要重新配置成原来主的交换机出口端的地址,并取消原来端口 IP,经过测试恢复正常。
另外附error-disable的处理方式:
http://sfwang.blog.51cto.com/441426/1254137/
相关文章推荐
- #分布式系统架构之# 事件驱动模式以及与之匹配的长时间处理过程讨论
- 记录一次局域网突发网络环路处理过程——全是血泪 推荐
- 一次网络严重丢包的故障处理过程 推荐
- 一步一步实现企业网络架构之一:利用WINS实现名称解析 推荐
- 一步一步实现企业网络架构之二:安装和配置DHCP 推荐
- 三层架构设计模式各层间的访问过程
- 网络数据流接收处理过程分析
- 主动模式下FTP的详细工作过程 推荐
- 模式和架构读书笔记《.NET模式-架构、设计与过程》一
- SQL注入渗透某网络安全公司的网站全过程
- vlc学习计划(6)--网络数据流接收处理过程分析
- MVC的处理过程及优点-学习Struts 2 不得不说的架构(1)
- SQL注入渗透某网络安全公司的网站全过程
- 一步一步实现企业网络架构之八:利用IIS建立和维护一个WEB服务器 推荐
- 推荐书籍系列(1):企业应用架构模式
- SQL注入渗透某网络安全公司的网站全过程
- 在NBMA网络广播模式下配置OSPF实际案例(配图)+详细验证过程