Qt::ConnectionType 解析
2016-03-03 17:30
309 查看
signal/slot在底层会使用三种方式传递消息。参见QObject::connect()方法:
bool QObject::connect ( const QObject * sender, const char * signal, const QObject * receiver, const char * method, Qt::ConnectionType type = Qt::AutoCompatConnection )
最后一个参数是就是传递消息的方式了,有四个取值:
Qt::DirectConnection
When emitted, the signal is immediately delivered to the slot.
假设当前有4个slot连接到QPushButton::clicked(bool),当按钮被按下时,QT就把这4个slot按连接的时间顺序调用一遍。显然这种方式不能跨线程(传递消息)。
Qt::QueuedConnection
When emitted, the signal is queued until the event loop is able to deliver it to the slot.
假设当前有4个slot连接到QPushButton::clicked(bool),当按钮被按下时,QT就把这个signal包装成一个 QEvent,放到消息队列里。QApplication::exec()或者线程的QThread::exec()会从消息队列里取消息,然后调用 signal关联的几个slot。这种方式既可以在线程内传递消息,也可以跨线程传递消息。
Qt::BlockingQueuedConnection
Same as QueuedConnection, except that the current thread blocks until the slot has been delivered. This connection type should only be used for receivers in a different thread. Note that misuse of this type can lead to dead locks in your application.
与Qt::QueuedConnection类似,但是会阻塞等到关联的slot都被执行。这里出现了阻塞这个词,说明它是专门用来多线程间传递消息的。
Qt::AutoConnection
If the signal is emitted from the thread in which the receiving object lives, the slot is invoked directly, as with Qt::DirectConnection; otherwise the signal is queued, as with Qt::QueuedConnection.
这种连接类型根据signal和slot是否在同一个线程里自动选择Qt::DirectConnection或Qt::QueuedConnection
这样看来,第一种类型的效率肯定比第二种高,毕竟第二种方式需要将消息存储到队列,而且可能会涉及到大对象的复制(考虑sig_produced(BigObject bo),bo需要复制到队列里)。
bool QObject::connect ( const QObject * sender, const char * signal, const QObject * receiver, const char * method, Qt::ConnectionType type = Qt::AutoCompatConnection )
最后一个参数是就是传递消息的方式了,有四个取值:
Qt::DirectConnection
When emitted, the signal is immediately delivered to the slot.
假设当前有4个slot连接到QPushButton::clicked(bool),当按钮被按下时,QT就把这4个slot按连接的时间顺序调用一遍。显然这种方式不能跨线程(传递消息)。
Qt::QueuedConnection
When emitted, the signal is queued until the event loop is able to deliver it to the slot.
假设当前有4个slot连接到QPushButton::clicked(bool),当按钮被按下时,QT就把这个signal包装成一个 QEvent,放到消息队列里。QApplication::exec()或者线程的QThread::exec()会从消息队列里取消息,然后调用 signal关联的几个slot。这种方式既可以在线程内传递消息,也可以跨线程传递消息。
Qt::BlockingQueuedConnection
Same as QueuedConnection, except that the current thread blocks until the slot has been delivered. This connection type should only be used for receivers in a different thread. Note that misuse of this type can lead to dead locks in your application.
与Qt::QueuedConnection类似,但是会阻塞等到关联的slot都被执行。这里出现了阻塞这个词,说明它是专门用来多线程间传递消息的。
Qt::AutoConnection
If the signal is emitted from the thread in which the receiving object lives, the slot is invoked directly, as with Qt::DirectConnection; otherwise the signal is queued, as with Qt::QueuedConnection.
这种连接类型根据signal和slot是否在同一个线程里自动选择Qt::DirectConnection或Qt::QueuedConnection
这样看来,第一种类型的效率肯定比第二种高,毕竟第二种方式需要将消息存储到队列,而且可能会涉及到大对象的复制(考虑sig_produced(BigObject bo),bo需要复制到队列里)。
相关文章推荐
- QT学习 第一章:基本对话框
- 使用Shiboken为C++和Qt库创建Python绑定
- Qt 5.6更新至RC版,最终版本近在咫尺
- Qt定时器和随机数详解
- Qt实现图片移动实例(图文教程)
- Qt for Android开发实例教程
- QModelIndex/Role/Model介紹<二>
- 基于PyQt5的快速开发框架QFramer
- OSX下安装PyQt
- ok6410开发板移植DirectFB手记
- 【笔记】给Qt内嵌一个Chrome吧
- 【算法】最短路径之A*搜索
- qt入门必备
- 在 Qt4 中使用 C++11
- Hello Word ~ v0.2.2 背单词软件发布 -- By WHYPRO
- ubuntu下opencv和qt的安装配置
- linux下opengl的安装(with qt)
- qt 学习小节
- QT编译时Cannot find -lGL
- QT的命名风格