接primsense 用rqt订阅发现rgb图和depth图巨卡
2015-09-04 19:26
411 查看
解决方案参考:http://answers.ros.org/question/77651/asus-xtion-on-usb-30-ros-hydro-ubuntu-1210/
概要如下:
"To get the device working I used OpenNI Unstable 1.5.4.0 (https://github.com/OpenNI/OpenNI.git)
and PrimeSense Sensor Unstable 5.1.2.1 (https://github.com/PrimeSense/Sensor.git)"
"After installing the driver it is necessary to change the "USB interface" that is used to BULK endpoints by uncommenting UsbInterface=2 in GlobalDefaults.ini (/usr/etc/primesense/GlobalDefaults.ini). I've also found it works when the interface is set to 0.
The following comment from the file explains the meaning of the parameters: ; USB interface to be used. 0 - FW Default, 1 - ISO endpoints, 2 - BULK endpoints. Default: Arm - 2, other platforms - 1"
装完重启后,问题基本解决,不过还是会出现:Warning: USB events thread - failed to set priority. This might cause loss of data...
补充:发现kinect用openni_camera驱动又无法启动了。。。。
解决办法:卸载ros-indigo-openni-camera, 卸载完会提示你会自动装freenect驱动,安装完后用 roslaunch freenect_launch freenect.launch启动kinect正常。然后又install ros-indigo-openni-camera,但还是无法启动。。。从此弃用。。。
概要如下:
"To get the device working I used OpenNI Unstable 1.5.4.0 (https://github.com/OpenNI/OpenNI.git)
and PrimeSense Sensor Unstable 5.1.2.1 (https://github.com/PrimeSense/Sensor.git)"
"After installing the driver it is necessary to change the "USB interface" that is used to BULK endpoints by uncommenting UsbInterface=2 in GlobalDefaults.ini (/usr/etc/primesense/GlobalDefaults.ini). I've also found it works when the interface is set to 0.
The following comment from the file explains the meaning of the parameters: ; USB interface to be used. 0 - FW Default, 1 - ISO endpoints, 2 - BULK endpoints. Default: Arm - 2, other platforms - 1"
装完重启后,问题基本解决,不过还是会出现:Warning: USB events thread - failed to set priority. This might cause loss of data...
补充:发现kinect用openni_camera驱动又无法启动了。。。。
解决办法:卸载ros-indigo-openni-camera, 卸载完会提示你会自动装freenect驱动,安装完后用 roslaunch freenect_launch freenect.launch启动kinect正常。然后又install ros-indigo-openni-camera,但还是无法启动。。。从此弃用。。。
相关文章推荐
- 自学QT之堆栈窗口
- QT,QT SDK, QT Creator 区别
- QT工程pro文件TEMPLATE变量说明
- QT跨目录编译及多工程集成
- Ubuntu12.04下安装Qt4.8.1
- Qt信号与槽
- window7配置Qt
- 自学QT之停靠窗口
- 源码安装Qt 5.4.2
- QTableView与QStandardItemModel基本使用方法
- 在QThread中使用QTimer
- QThread的一种用法
- 自学QT之实现窗口分割QSplitter的使用
- 自学QT之判断输入内容实现按钮可用或者不可用
- 记录Qt的一个诡异Bug
- [转载]Qt之中文显示(QMessageBox、QLineEdit右键菜单等)
- 如何在Qt中使用自定义数据类型
- [转载]Qt之自定义界面(二)添加最小化、关闭按钮、添加背景
- Qt 中如何捕获窗口停用和激活的消息
- vs2012的属性管理器和项目属性的一些问题(opencv+qt+vs2012)