eCos学习笔记之中断处理代码分析(转)

中断处理代码分析：
.macro    hal_vectors_init //中断向量初始化，packages/hal/mips/ref4955/v2_0/include/platform.inc
        # If we don~t play nice with a ROM monitor, copy the required
        # vectors into the proper location.
    la    t0,0x80000000        # dest addr //有些MIPS变种不需要处理tlb的异常
    la    t1,utlb_vector        # source addr
    la    t3,utlb_vector_end    # end dest addr
1:   
    lw    v0,0(t1)        # get word
    addi    t1,t1,4
    sw    v0,0(t0)        # write word
    addi    t0,t0,4
    bne    t1,t3,1b
     nop

    la    t0,0x80000180        # dest addr //将other_vector拷贝到0x80000180处，完成中断向量的安装
    la    t1,other_vector        # source addr
    la    t3,other_vector_end    # end dest addr
1:   
    lw    v0,0(t1)        # get word
    addi    t1,t1,4
    sw    v0,0(t0)        # write word
    addi    t0,t0,4
    bne    t1,t3,1b
     nop
    .endm
   
.section ".other_vector","ax" //中断处理代码安装的位置

    # Common vector at 0x80000080 or 0xBFC00180
    
FUNC_START(other_vector) //MIPS异常处理程序的入口，packages/hal/mips/arch/v2_0/src/vectors.S
    mfc0    k0,cause        # K0 = exception cause //读取cause寄存器
    nop
    andi    k0,k0,0x7F        # isolate exception code //取cause寄存器中的ExcCode值
    la    k1,hal_vsr_table    # address of VSR table //取VSR表的基地址
    add    k1,k1,k0        # offset of VSR entry //根据ExcCode值取得VSR表的入口地址
    lw    k1,0(k1)        # k1 = pointer to VSR //取得VSR表中对应处理程序的地址
    jr    k1            # go there //跳转执行
    nop                # (delay slot)
FUNC_END(other_vector)

## VSR table.
## The main interrupt code indirects through here to find the VSR
## to execute for each architecture defined interrupt.
## This is only used for simulated targets, on real targets a fixed location VSR
## table is now allocated at 0x80000100.

#ifndef CYG_HAL_MIPS_VSR_TABLE_DEFINED
    
##    .section ".vsr_table","a" //VSR表
    
    .data //VSR表在data段中
            
    .globl    hal_vsr_table

hal_vsr_table:    
    .long    __default_interrupt_vsr    //定义了64个interrupt入口
    .rept    63
    .long    __default_exception_vsr    
    .endr

#endif    

## Default interrupt VSR.
## Saves machine state and calls appropriate ISR. When done, calls
## interrupt_end() to finish up and possibly reschedule.    

FUNC_START(__default_interrupt_vsr) //缺省的中断处理程序

    
    # We enter here with all of the CPU state still
    # in its registers except:
    # K0 = vector index
    # K1 = address of this function

    move    k1,sp            # K1 = original SP //保存原始SP
        
    addi    sp,sp,-mips_exception_decrement //分配stack空间
                # space for registers + safety margin

    sw    k0,mipsreg_vector(sp)    # store vector //将异常类型（即ExcCode值）存入堆栈

    # store GPRs //保存通用寄存器
    .set    noat
    sgpr    0,sp
    sgpr    1,sp
    sgpr    2,sp
    sgpr    3,sp
    sgpr    4,sp
    sgpr    5,sp
    sgpr    6,sp
    sgpr    7,sp
    sgpr    8,sp
    sgpr    9,sp
    sgpr    10,sp
    sgpr    11,sp
    sgpr    12,sp
    sgpr    13,sp
    sgpr    14,sp
    sgpr    15,sp
    sgpr    16,sp
    sgpr    17,sp
    sgpr    18,sp
    sgpr    19,sp
    sgpr    20,sp
    sgpr    21,sp
    sgpr    22,sp
    sgpr    23,sp
    sgpr    24,sp
    sgpr    25,sp
#    sgpr    26,sp    # == K0
#    sgpr    27,sp    # == K1
    sgpr    28,sp    # == GP
#    sgpr    29,sp    # == SP
    sgpr    30,sp    # == FP
    sgpr    31,sp    # == RA
    .set    at
    
    mfhi    a0 //保存hi和lo寄存器
    mflo    a1
    shi    a0,sp
    slo    a1,sp

    # K1 contains original SP
    ssp    k1,sp            # store in reg dump    //保存原始SP到新的stack中的特殊位置上
        
    mfc0    t1,status //保存status，cachectrl和epc寄存器
    mfc0    t2,cachectrl
    mvafc0    t3,epc
    
    sw    t1,mipsreg_sr(sp)
    sw    t2,mipsreg_cachectrl(sp)
    sva    t3,mipsreg_pc(sp) //epc寄存器

    hal_fpu_save sp //保存浮点寄存器，packages/hal/mips/arch/v2_0/include/arch.inc，如果处理器没有fpu则该宏为空，Lupine没有浮点寄存器
        //到此为止处理器的状态已经保存到栈上了
    # The machine state is now all saved on the stack.

    # Load Global Pointer register.
    la    gp,_gp //加载gp指针
    
#ifdef CYGFUN_HAL_COMMON_KERNEL_SUPPORT            
    .extern    cyg_scheduler_sched_lock
    la    v0,cyg_scheduler_sched_lock //锁住调度器
    lw    a0,0(v0)
    addi    a0,a0,1
    sw    a0,0(v0)
#endif

    move    s0,sp                # save pointer to saved state //取sp指针，留做后用

#ifdef CYGIMP_HAL_COMMON_INTERRUPTS_USE_INTERRUPT_STACK //如果中断使用独立堆栈

    la    a0,__interrupt_stack        # a0 = stack top //栈顶指针
    la    a1,__interrupt_stack_base    # a1 = stack base //栈基址，定义如下：
                       .bss
       .balign 16
                       .global cyg_interrupt_stack_base
                       cyg_interrupt_stack_base 
                   __interrupt_stack_base:
                       .rept CYGNUM_HAL_COMMON_INTERRUPTS_STACK_SIZE //stack的大小
                       .byte 0
                       .endr
    sub    a3,sp,a1            # a3 = sp - base //现在的sp是否比__interrupt_stack_base小
    bltz    a3,1f                # not on istack if < 0 
    nop                    # delay slot
    sub    t0,a0,sp            # t0 = top - sp //现在的sp是否比__interrupt_stack大
    bgtz    t0,8f                # already on istack if > 0 
    nop                    # delay slot
1:    
    move    sp,a0                # switch to istack //not on istack
8:
    addi    sp,sp,-8            # space for old SP //on istack，为保存现在的sp留出空间
                        # (8 to keep dword alignment!)
    sw    s0,0(sp)            # save old SP on stack //保存现在的sp
#endif
            
    subu    sp,sp,mips_stack_frame_size    # make a null frame     //做一个空的栈帧（32bytes）
    # Need to set up back pointers etc. ???

    # Decode external interrupt via interrupt controller

    hal_intc_decode    s2 //根据cause寄存器的IP位解码，返回IP号，packages/hal/mips/tx39/v2_0/include/variant.inc

    # Here, s2 contains the number of the interrupt being serviced,
    # we need to derive from that the vector number to call in the ISR
    # table.
    
    hal_intc_translate s2,s1 //packages/hal/mips/tx39/v2_0/include/variant.inc
    
    # Here s1 is the number of the vector to be called and s2 is
    # the number of the interrupt being serviced. 

    hal_diag_intr_start //中断诊断程序，可以不实现，packages/hal/mips/vrc437x/v2_0/include/platform.inc
        
#if defined(CYGPKG_KERNEL_INSTRUMENT) && defined(CYGDBG_KERNEL_INSTRUMENT_INTR)

    # Call cyg_instrument to record that this interrupt is being raised. //记录程序
        
    li    a0,0x0301            # a0 = type = INTR,RAISE
    move    a1,s1                # a1 = vector number
    jal    cyg_instrument            # call instrument function
     move    a2,s2                # a2 = interrupt number
#endif

#if defined(CYGDBG_HAL_MIPS_DEBUG_GDB_CTRLC_SUPPORT)
    # If we are supporting Ctrl-C interrupts from GDB, we must squirrel
    # away a pointer to the save interrupt state here so that we can
    # plant a breakpoint at some later time.
    
    .extern    hal_saved_interrupt_state //使用GDB stub调试时，用于保存中断状态
    la    v0,hal_saved_interrupt_state
    sw    s0,0(v0) //s0是sp指针
    
#endif
    
    sll    s1,s1,2                # s1 = byte offset of vector //根据中断向量号计算中断向量偏移
    //在此之前都是禁用中断的
    hal_cpu_except_enable            # reenable exceptions //启用中断，packages/hal/mips/arch/v2_0/include/arch.inc
    la    t2,hal_interrupt_handlers    # handler table //加载中断处理程序表，如果未定以CYG_HAL_MIPS_ISR_TABLES_DEFINED，该表在packages/hal/mips/arch/v2_0/src/vectors.S中，否则根据platform不同有不同定义，如packages/hal/mips/tx39/v2_0/src/variant.S
    add    t2,t2,s1            # address of ISR ptr //根据中断向量号计算在中断处理程序表中的偏移
    lw    t2,0(t2)            # ISR pointer //取中断处理程序地址

    la    a1,hal_interrupt_data        # data table //加载中断处理程序数据表，定义位置与hal_interrupts_handlers一样
    add    a1,a1,s1            # address of data ptr //计算中断处理程序数据偏移
    lw    a1,0(a1)            # Data pointer //将中断处理程序数据地址存入a1，作为参数

    move    a0,s2                # pass interrupt number //将中断号存入a0寄存器，作为参数

    jalr    t2                # call ISR via t2 //调用具体的中断处理程序，有两个参数，分别是中断向量号和中断处理程序数据
    nop                    # (delay slot)

#ifdef CYGIMP_HAL_COMMON_INTERRUPTS_USE_INTERRUPT_STACK

    # If we are returning from the last nested interrupt, move back
    # to the thread stack. interrupt_end() must be called on the
    # thread stack since it potentially causes a context switch.
    # Since we have arranged for the top of stack location to
    # contain the sp we need to go back to here, just pop it off
    # and put it in SP.

    
    lw    sp,mips_stack_frame_size(sp)    # sp = *sp
    subu    sp,sp,mips_stack_frame_size    # make a null frame        
#endif
    
#ifdef CYGFUN_HAL_COMMON_KERNEL_SUPPORT

    # We only need to call _interrupt_end() when there is a kernel
    # present to do any tidying up.
    
    # On return v0 bit 1 will indicate whether a DSR is
    # to be posted. Pass this together with a pointer to
    # the interrupt object we have just used to the
    # interrupt tidy up routine.

    # Note that s0, s1 and s2 are defined to be preserved across
    # calls by the calling convention, so they still contain
    # the register dump, the vector offset and the interrupt number
    # respectively.

    move    s2,v0 //临时保存中断处理程序的返回值
        
    la    a1,hal_interrupt_objects    # interrupt object table //取中断对象，定义位置与hal_interrupt_handlers一样，将地址存入a1，用作参数
    add    a1,a1,s1            # address of object ptr
    lw    a1,0(a1)            # a1 = object ptr

    move    a2,s0                # arg3 = saved register dump //堆栈指针存入a2，作为参数
    
    .extern    interrupt_end
    jal    interrupt_end            # call into C to finish off //调用interrupt_end做后面的处理（挂起DSR，解锁调度器，执行DSR），有三个参数，分别是ISR返回值，中断对象，堆栈指针，此处可能导致线程上下文切换
     move    a0,v0                # put ISR result in arg0 //将ISR返回值放入a0，用作参数
    
    move    v0,s2                # return value from isr //恢复ISR返回值
#endif
                
restore_state: //从中断处理返回的例程
#if defined(CYGSEM_HAL_USE_ROM_MONITOR_CygMon)
    move    k0,v0
#endif

    # All done, restore CPU state and continue

    addi    sp,sp,mips_stack_frame_size    # retrieve CPU state ptr //释放这块堆栈

    # Disable interrupts again while we restore state. 
    hal_cpu_int_disable //再次禁用中断直到现场恢复，packages/hal/mips/arch/v2_0/include/arch.inc

    hal_diag_restore //中断恢复的诊断程序

    hal_fpu_load sp //恢复fpu寄存器，packages/hal/mips/arch/v2_0/include/arch.inc

    lw    t0,mipsreg_cachectrl(sp) //恢复cachectrl，hi和lo寄存器
    lhi    t1,sp
    llo    t2,sp

    mtc0    t0,cachectrl
    mthi    t1
    mtlo    t2

    # load GPRs //恢复通用寄存器
    .set    noat
#    lgpr    0,sp
    lgpr    1,sp
    lgpr    2,sp
    lgpr    3,sp
    lgpr    4,sp
    lgpr    5,sp
    lgpr    6,sp
    lgpr    7,sp
    lgpr    8,sp
    lgpr    9,sp
    lgpr    10,sp
    lgpr    11,sp
    lgpr    12,sp
    lgpr    13,sp
    lgpr    14,sp
    lgpr    15,sp
    lgpr    16,sp
    lgpr    17,sp
    lgpr    18,sp
    lgpr    19,sp
    lgpr    20,sp
    lgpr    21,sp
    lgpr    22,sp
    lgpr    23,sp
    lgpr    24,sp
    lgpr    25,sp
#    lgpr    26,sp    # == K0
#    lgpr    27,sp    # == K1
    lgpr    28,sp    # == GP
#    lgpr    29,sp    # == SP
    lgpr    30,sp    # == FP
    lgpr    31,sp    # == RA
    .set    at

#if defined(CYGSEM_HAL_USE_ROM_MONITOR_CygMon)

        # If we have a Cygmon that wants to listen to network interrupts, then
        # the return code from the earlier call to hal_default_isr() will
        # have been negative to indicate this. So we jump into Cygmon here
        # because Cygmon requires the processor state to be the same as when
        # the interrupt was taken, but with k0 as the exception number.
        
    bgez    k0,1f
    nop
    # Check for new cygmon
    sw    k0,(mipsreg_regs+26*4)(sp)    # save k0
    la    k1,0x80000100 + 41*4        # New cygmon "magic" id
    lw    k1,0(k1)
    lui    k0,0x55aa
    ori    k0,0x4321
    bne    k0,k1,1f
            
    # Need to let cygmon handle this
    la    k1,0x80000100 + 39*4        # stub entry vector
    lw    k0,(mipsreg_regs+26*4)(sp)    # restore k0
    lw    k1,0(k1)
    lw    sp,(mipsreg_regs+29*4)(sp)    # restore SP
    sll    k0,1                # clear bit 31.
    jr    k1
        srl    k0,1
    1:
#endif

    lw    k1,mipsreg_sr(sp)        # K1 = saved SR //恢复status寄存器

#if 0 < CYGINT_HAL_MIPS_INTERRUPT_RETURN_KEEP_SR_IM
    # Keep the current settings of the IM[7:0] bits within the status
    # register.  These may be used as interrupt masks, so if an ISR or
    # DSR masks interrupts they must be preserved.
    # If they are not used, then this does no harm.
    ori    k0,zero,0xff00
    nor    k0,k0,k0            # 0xffff00ff
    and    k1,k1,k0            # all interrupts disabled

    mfc0    k0,status            # V0 = current SR
    nop
    nop
    andi    k0,k0,0xff00            # preserve interrupt set //保留IM[7:0]
    or    k1,k1,k0            # insert into "saved SR"
#endif // 0 < CYGINT_HAL_MIPS_INTERRUPT_RETURN_KEEP_SR_IM
    lva    k0,mipsreg_pc(sp)        # K0 = return PC //取epc寄存器到k0中
    lsp    sp,sp                # load SP //恢复sp寄存器

    # Invoke CPU specific mechanism for returning from this
    # exception
    
    hal_cpu_eret k0,k1 //从异常恢复，packages/hal/mips/arch/v2_0/include/arch.inc，k0是epc寄存器（即返回地址），k1是status寄存器，该宏定义如下：
                   .macro    hal_cpu_eret pc,sr
                   mtc0    /sr,status            # Load status register
                   nop
                   nop
                   nop
                   sync                    # settle things down
                   jr    /pc                # jump back to interrupted code
                   rfe                    # restore state    (delay slot)    
                   .endm
FUNC_END(__default_interrupt_vsr)
/article/2515816.html