Slow performance occurs when you copy data to a TCP server by using a Windows Sockets API program
Article ID: 823764 - View products that
this article applies to.
System TipThis article applies to a different version of Windows than the one you are using.
Content in this article may not be relevant to you. Visit
the Windows 7 Solution Center
Expand all | Collapse
all
On
This Page
SYMPTOMS
CAUSE
WORKAROUND
Method
1: Use Blocking Sockets
Method
2: Make the Socket Send Buffer Size Larger Than the Program Send Buffer Size
Method
3: Modify the TCP/IP Settings on the TCP Server
Method
4: Modify the buffering behavior in Afd.sys for non-blocking sockets
STATUS
REFERENCES
Properties
Give
Feedback
When you run a program that uses the Windows Sockets API, you may experience slow performance when you copy data to a TCP server.
If you make a network trace with a network sniffer such as Microsoft Network Monitor, the TCP server sends a TCP ACK segment to the last TCP segment in a TCP data stream in the delayed acknowledgement timer (also known as the delayed
ACK timer). By default, for Windows operating systems, the value for this timer is 200 milliseconds (ms). A typical data flow for sending 64 kilobytes (KB) of data looks similar to the following
sequence:
Client->Server 1460 bytes
Client->Server 1460 bytes
Server->Client ACK
Client->Server 1460 bytes
Client->Server 1460 bytes
Server->Client ACK
....
Client->Server 1460 bytes
Client->Server 1460 bytes
Server->Client ACK-PUSH
Client->Server 1296 bytes
-> delayed ACK 200 ms
Back
to the top | Give
Feedback
This problem occurs because of the architectural behavior of the Windows Sockets API and Afd.sys. This problem occurs if all the following conditions are true:
The Windows Sockets program uses non-blocking sockets.
A single send call or WSASend call fills the whole underlying socket send buffer.
For example, the program uses the Windows Sockets setsockopt function to change the default socket send buffer to 32 KB during its socket initialization routines:
setsockopt( sock, SOL_SOCKET, 32768, (char *) &val, sizeof( int ) );
Later, when the program sends data, it issues a send call or a WSASend call and sends 64 KB of data during each send:
send(socket, pWrBuffer, 65536, 0);
In this scenario, each time the program issues a send call of 64 KB of data, the program returns aSOCKET_ERROR error code if the underlying 32-KB socket buffer is completely filled. After
it calls theWSAGetLastError function, the program receives the WSAEWOULDBLOCK error code. Most programs use the Windows Sockets select function to check the status of the socket. In
this scenario, the select function does not report the socket as writable until the client receives the outstanding TCP ACK segment. By default in a Windows environment, this may take as long as 200 ms because
of the delayed acknowledgement algorithm.
The remote TCP server acknowledges all the TCP segments before the client sends the last TCP segment with the push bit set.
Back
to the top | Give
Feedback
To work around this problem, use any of the following methods.
Method 1: Use Blocking Sockets
This problem only occurs with non-blocking sockets. When you use a blocking socket, this problem does not occur because Afd.sys handles the socket buffer differently. For
more information about blocking and non-blocking socket programming, see the Microsoft Platform SDK documentation.
Method 2: Make the Socket Send Buffer Size Larger Than the Program Send Buffer Size
To modify the socket send buffer, use the Windows Sockets getsockopt function to determine the current socket send buffer size (SO_SNDBUF), and then use the setsockopt function to set the socket send
buffer size. When you are finished, the SO_SNDBUF value must be at least 1 byte larger than the program send buffer size.
Modify the send call or the WSASend call to specify a buffer size at least 1 byte smaller than the SO_SNDBUF value. In the earlier example in the "Cause" section of this
article, you could modify thesetsockopt call to the following value,
setsockopt( sock, SOL_SOCKET, 65537, (char *) &val, sizeof( int ) );
or you could modify the send call to the following value:
send(socket, pWrBuffer, 32767, 0);
You could also use any combination of these values.
Method 3: Modify the TCP/IP Settings on the TCP Server
Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the
registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can
restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
322756 How
to back up and restore the registry in Windows
Modify the TCP/IP settings on the TCP server to immediately acknowledge incoming TCP segments. This workaround works best in an environment that has a large client installation base and where you cannot
change the program's behavior. For scenarios where the remote TCP server runs on a Windows-based server, you must modify the registry of the remote server. For other operating systems, see the
operating system's documentation for information about how to change the delayed acknowledgement timer.
On a server that runs Windows 2000, follow these steps:
Start Registry Editor (Regedit.exe).
Locate and then click the following registry subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\<Interface GUID>
On the Edit menu, click Add Value, and then create the following registry value:
Value name: TcpDelAckTicks
Data type: REG_DWORD
Value data: 0
Quit Registry Editor.
Restart Windows for this change to take effect.
On a server that runs Windows XP or Windows Server 2003, follow these steps:
Start Registry Editor.
Locate and then click the following registry subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\<Interface GUID>
On the Edit menu, point to New, and then click DWORD
Value.
Name the new value TcpAckFrequency, and assign it a value of 1.
Quit Registry Editor.
Restart Windows for this change to take effect.
Method 4: Modify the buffering behavior in Afd.sys for non-blocking sockets
Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the
registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can
restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
322756 How
to back up and restore the registry in Windows
Note This registry key is only available for Windows Server 2003 with Service Pack 1 and subsequent service packs.
Click Start, type regedit.exe, and then click OK.
Locate and then click the following registry subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\AFD\Parameters
On the Edit menu, point to New, and then click DWORD
Value.
Name the new value NonBlockingSendSpecialBuffering, and assign it a value of 1.
Exit Registry Editor.
Restart Windows for this change to take effect.
Back
to the top | Give
Feedback
Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section.
Back
to the top | Give
Feedback
328890 New
registry entry for controlling the TCP Acknowledgment (ACK) behavior in Windows XP and in Windows Server 2003
Back
to the top | Give
Feedback
Article ID: 823764 - Last Review: February 28, 2007 - Revision: 5.6
APPLIES TO
Microsoft Windows Server 2003, Enterprise Edition (32-bit x86)
Microsoft Windows Server 2003, Standard Edition (32-bit x86)
Microsoft Windows Server 2003, Web Edition
Microsoft Windows XP Home Edition
Microsoft Windows XP Professional
Microsoft Windows 2000 Advanced Server
Microsoft Windows 2000 Professional Edition
Microsoft Windows 2000 Server
Windows Server 2008 Datacenter without Hyper-V
Windows Server 2008 Enterprise without Hyper-V
Windows Server 2008 for Itanium-Based Systems
Windows Server 2008 Standard without Hyper-V
Windows Server 2008 Datacenter
Windows Server 2008 Enterprise
Windows Server 2008 Standard
Windows Web Server 2008
Back
to the top | Give
Feedback
|
